Jump to content
SAU Community

Recommended Posts

Who sells Motul 10w40 oils? i have always gone to Supercheap and gotten Mobil1 Fully Synthetic 0w40 but that's a little too light for summer.

Need 10w40..

only a quick question for a quick answer, thanks SAUWA :devil:

Last lot I got was from Repco. Suggest ring and ask as they do not always hold in stock.

Cheers

dirt garage (moto x place) in vic park opposite maccas, where i got mine from(altho my mate knows the owner), they had to order it in. took a couple of days.

actually you'll prob find alot of bikes place are motul suppliers.

Edited by Brad3416

I know where Tenagah is now and I know they deal with Motul, they are in a temporary shop in Wangara while another shop is prepare. BUT, they don't work weekends...

Edited by Topaz

royal purple 10 - 40

A1 performance in myaree. =)

made the same swap as u are... i was using mobil 1 0-40 but swapped over for summer 10-40...

Edited by br3ndan
People just don't understand and often wont be told. Many resellers dont know anything about oil etc and often miss lead customers.

Like I was today by a female sales person...

Me: The 300V Chrono is only 4 litres and I will probably need about 4.5

Her: Just leave some oil in the engine before refilling

Me: ......................

Motul 300Vif you have alot of money to throw around. 109$ for 4L, 57$ for 2L

Otherwise Motul 4100 Turbolight 5L for 59$.

Motoquipe sell it for very cheap. Repco also stock it at 120% what motoqipe charge

Or go royal purple.

why? they have the same hot viscosity, the 10-40 is just thicker when cold, hardly better....

thats exactly it...

its not that cold anymore so dont really need the '0' rating.

Both are top notch oils, mobil 1 and royal purple... and similar pricing =)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...