Jump to content
SAU Community

Recommended Posts

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

i was thinking of a vent in the bonnet above the pod filter as well, however the main problem then is water getting into ur engine bay and if driving ur induction system! would need to have like a drainage system or like a vent cover so in the rain u can drive, but no cold air :cheers:

I wouldnt know which one is the loudest, but heres a comparison somebody did between different filters. Apexi was the best :D

http://www.mkiv.com/techarticles/filters_test/2/

I have an Apexi pod, but I found that unless you're using a cold air partition, the HKS gives you noticably more power. I *think* this is because it faces more to the front and has more of a face to the incoming cold air, whereas the Apexi pod can suck in hot air from the sides. But when I put the box in, the power was pretty much the same for both (I couldn't tell the difference anyway).

If you didn't want a cold air box/partition, I would probably prefer the HKS filter or another one of a similar shape. Although then you have to worry about the particle filtration, which was my main concern when choosing the Apexi pod.

  • 1 month later...

I've got a Blitz SUS LM on mine, and yup, its friggin loud. You can hear it sucking, even when slightly cruising. With the window down its probably the loudest thing you can hear in my car! Its kinda cool, and annoying at others - but its staying on.

So if a cop pulls any of you over, and pops your bonnet, and sees a pod/s they will defect you right?

I had a large K&N pod on my old car (Alfa Romeo) but it was on the end of a pipe which I had custom made to sit down very low away from the engine and close (but not too close so that it sucked up water from puddles in the rain) to the road. And the cops would never have found it because you couldn't see it but damn could you hear it!!!!!!

I want to install duel pods in my RB26 but I don't want to get defected!

Guest RedLineGTR

Best Bet are get a photo of it possbily and post it in the for sale section (parts) and most likly some one will buy it u just have to figure out a price to sell it...how much u ask?? i have no idea. I have found that people have still been buying them, so all i can say good luck.

Cheers Rob

Guest RedLineGTR

Also those tests are with a high concentration of particles and toxins, and it never gets that bad on "normal" roads, but to stop the really microscopic particles u can’t use foam at all. Best bets are for a Mesh type filter wet or dry, out of the tests I would go for the apexi one but i personally want one that i can clean nothing is clear forever and will eventually restrict flow, I myself have a k&n filter with the light oil it has and the Mesh type filter I’m pretty sure its doing a good job (I don’t believe 100% those test u don’t know if they are new etc). My 2 Cents.

For those running the Blitz Sus LM are there any temp problems and how often do you clean them, if at all?

I'm thinking of buying one, but i can't find the Stainlees steel one. Only the..er..non stainles steel. hehe

The review, earlier, shows that it does not filter that well. Has anybody had any filtration problems while using a Pod?

I currently have a K&N panel filter in my standard air box. You can hear the induction noise from the inside and a slight BOV sound, but it's not that loud. If the radio is on all you hear is the exchaust......and the radio of course!! :wassup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Sane enough. Remove the roof liner, because the acid will go everywhere.
    • Thanks guys, I really appreciate the help and experienced opinions.  I have spent a lot of my life working on boats so I'm pretty good with fibreglass. I'll take everybody's advice in here;  I'll cut a little more of the 2nd layer away as it's a bit crunchy rust and also it's sitting high now. Then I'll wire brush it all a bit to get off anything loose, then I'll soak the bejesus out of it all in rust converter. I'll make sure to get a little hose piece and feed it into all the holes and gaps between the roof layers. Then I'll fibreglass up the holes.  Then I'll get a pallet of filler and mix it with 3 buckets of hardener and hope that is enough to build up the roof corner.  Does that sound sane? Is one type of filler better than others for this?
    • My goals for it atm are to get it registered, respray and some mild power gains eventually... I picked up the car from an elderly gentleman near the border of NSW and VIC, its honestly a bit rough and looks like its been driven on a farm (because there was so much dirt underneath). Last week I dropped the subframe and emptied the old fuel out + added a new fuel pump (think the old one went bad from old fuel). Now I'm onto fixing a coolant leak at the rear of the engine + adding a new radiator as the old one is corroded. After that i have a new bumper, coils (as the old were leaking) and lots more
    • Welcome buddy! Plenty on here and YouTube. What are your plans for it? Good luck with the Rwc and Rego bud!
    • Love this so much! Please post a photo when you have a bike on the trailer.  I was a little bit worried about having a tow bar on the Skyline, but having it hidden behind the number plate is genius
×
×
  • Create New...