Jump to content
SAU Community

Recommended Posts

ok so did a track day yesterday. noticed when driving home there is an oil smell.

here's the senario. if you have windows down you can smell oil, when windows up no smell, windows up fan on no smell as well. it only seems to be when either window is down>

i've checked every thing, got my dad to take it work and put on the hoist and couldn't find anything. iv'e degreased everything front to back top to bottom and still can see nothing

does anyone have an idea.

Link to comment
https://www.sau.com.au/forums/topic/294229-oil-smell-after-track-day/
Share on other sites

I had the same issue but I had some lumpy cams that produced a whole load of blow back into my catch can. My catch can had filters that oil fumes were coming out of. Not too sure if this is your issue but it may provide you with a starting point.

I had the same issue but I had some lumpy cams that produced a whole load of blow back into my catch can. My catch can had filters that oil fumes were coming out of. Not too sure if this is your issue but it may provide you with a starting point.

cams and blow are not related in any way shape or form.

How much boost do you run - stock or above 1 bar?

I found on my R33 GTR with steel wheel hi-flows that at 1 Bar you get oil vapor mixing in the crank case. This is because on the track you are on boost a hell of a lot longer than on the street. In my case I have a breather off the valve cover hoses that started to "ooze" oil out. The stock hoses also actually pipe the breather link into the plenum just below the throttle linkage which pipes the oil filled air back into the induction system.

Even though I now have a just jap catch can with return lines into the valve cover, on High boost situations I still get oil spitting out the back of the car. Check around your exhaust. If this is the case then what you are smelling is the oil in your exhaust system (coated inside). Also check where your breather lines go - in my case made a mess around the ABS unit.

But Trent, I removed my catch can and it had a fair level of oil (enough to tip out). It seemed that oil vapors were blowing into the catch can.

You have blow by, yes... Your cams won't cause it is what Trent is saying.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
×
×
  • Create New...