Jump to content
SAU Community

Recommended Posts

  • Replies 164
  • Created
  • Last Reply

Top Posters In This Topic

hey buddy, sorry for late reply, do have all the lines however matt might be needing them with his new engine, but will double check as i think i have a second set aswell of all the lines somewhere, will chase it up and get back to you,(Troy)

Thanks mate. Let me know.

Hey mate,

Do you the have front inner splash guards?

Mike

I'll shot gun this answer as I also wanted this! :D

He's apparently keeping it unless he's changed his mind. I'm also after this.

You got complete stock airbox (snorkel included)?

Also, RHS A-pillar trim if there aren't any holes or marks at all?

If so, how much posted to 3199 - PM if you prefer to.

Cheers

Grant

Well?

sorry everyone for slow replys working 12 hour days

- sorry my brother in law is keeping inner guards because they are in good cond, he has gtr

-do not have complete air box

-selling a pillar trims together as they have the standard tweeters in them price is in the list, would be 150 plus postage

costs, thay have very few minor scratches

Matt,

Thanks for getting back to me.

I think I'll pass on A-pillar as I'm only after RHS anyway.

Also PM me your best price on PFC HC (is it FCC3 suitable for BNR32/BCNR33)?

Cheers

Grant

I bought the brakes, and just wanted to say that Troy's an honest seller. After looking at the car, it would have been easy for someone dodgy to to dodge it up and sell it with the rust covered but he's chosen to sell the parts and be legit about it all. I'd trust this bloke y'all!

Yeah, Troy is a top bloke...wrapped everything very well and prompt communication and postage too! Awesome! I've left traders comments for you mate - please do the same for me too! THanks.

-sorry mike, wont be able to get you power window motor in time as i am going away for work for two weeks, and a mate might be taking whole door anyway.

-sorry woo hoo the drivers control module is gone also

-Darkryda someone in adelaide has put shotgun on steering wheel already if it falls through will let you know.

-front inner guards are sold already including all diffusers that are under car(godzilla4me)

-goodwin front bar (both) are sold

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...