Jump to content
SAU Community

Recommended Posts

Just in case anyone is interested, I can get hold of the Field 'One Touch Connector' for most cars.

This sits between your ECU and car harness, allowing you to connect electronic devices to the ECU harness without cutting the factory wires.

Example

The unit comprises of a male and female sockets, with all interconnecting wires...I have the wiring diagrams for most cars, showing all relevant connections as well.

Dan

Can you get them for R31 GTS-X Coupes

I should be able to with a little bit of searching, most of them are only applicable to cars after 1988...but can't see why not considering it has an RB20DET.

Dan

Just as a guide the following are available:

Skyline R32, R33, R34 and GTR in all models (finding out about R31 should not be an issue though)

Silvia S13,14,15

180SX

300ZX

NX coupe

Stagea

Other popular makes and models

Toyota: Supra, MR2, Rav 4, Starlet, Celica etc

Mitsubishi: GTO, FTO, EVO etc

Subaru: WRX, Liberty etc

Honda: Integra, S2000 etc

Mazda: RX7, MX-5, MX-6 etc

Suzuki & Daihatsu

If you don’t see the your model listed just post it, and I’ll get back to you.

Dan

Dan, I al pretty keen, i need to er... *clean up* some wiring in my car...

$250 Delivered to Sydney eh? I'll see if i can organise a few people to get some to make it a bit cheaper.

Yeah it's good for *cleaning*....all those showy wires in funny places :D

Yeah the more the merrier, will get prices down a bit....just note payement has to be in full before ordering.

Dan

If delivering to you guys as well, the closest I could get to that is $215 each...for 10 people.

And that's if they're for an R32 or R33 GTS & GTSt and R32,R33,R34 GTR...I'd be hassling the N/A guys on this one too :D

Dan

Seeing that they're 10,000 yen for all Skyline models except for non-GTR R34 flavours (which are 12,000 yen), if you can get it down to $200 delivered for an R33 GTR harness, I'll take one.

http://www.field-net.co.jp/lineup/onetouch/op.html

All Skylines except non-GTR R34s  CN-2 10,000 Yen

Non-GTR R34s CN-10 12,000 Yen

P.S. Good discounts are available when you buy more than one of each type: http://exa.biz/shouhin/store_onetouch_2.html

Seeing that they're 10,000 yen for all Skyline models except for non-GTR R34 flavours (which are 12,000 yen), if you can get it down to $200 delivered for an R33 GTR harness, I'll take one.

http://www.field-net.co.jp/lineup/onetouch/op.html

All Skylines except non-GTR R34s   CN-2   10,000 Yen

Non-GTR R34s   CN-10   12,000 Yen

P.S. Good discounts are available when you buy more than one of each type: http://exa.biz/shouhin/store_onetouch_2.html

If you start adding local Japanese tax (5%) and the fact when you buy from Field, Australian customs DO hit you with import tax...then $215 is very fair.

So anyone in for $215?

OK I'll do them for $200 including delivery in Oz.....providing I get 10 people...and you all give a $5 donation to the forum.

Can't say much fairer than that....Prank, you want to make this a sticky to get the numbers up?

Merli forgot to mention local Japanese tax, and the fact as it comes from Field (the manufacturer), import duty tax is payable.

Dan

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...