Jump to content
SAU Community

Recommended Posts

i had this issue as well... mainly happend after i installed my stereo... i found it was because the hose was closed behind the console where the stereo is. Theres a little sensor type vent thing in the console/dash surround which looks like about 3 slits... at the back of these slits is a hose... i uncrimped this and it worked fine again... altho now it takes AGES to get cold... i think it just needs regasing.

Hey there

I just got my AC fixed 2 weeks ago, my compressor died - Compressors tend to go anywhere up to 250 for a 2nd hand one from a wrecker, but can be picked up as cheap as 150..

If you need it checked out, go to a place called "Norms Auto Air" (03) 9876 8611 @ 5/401 Maroondah Hwy Ringwood

He's a genuine bloke and will look after you, there are so many sharks out there in the Automotive AC industry!!!!!

BTW Tell him chicane with the red R33 who's compressor died sent you :cheers:

hey all just readin this thread and thought i would post a reply seens i am an air conditioner fitter and repair as well as a auto elec

well my r33 just did a compressor last week new ones i found are ex japan thats through my nissan dealer and well he said they are bout 1000 dollas delivered which isnt taht dear cos most on various aussie cars are bout 500 to 800 bucks

just for the comp

now if it is the comp you will need a regas and if want it to last as long as possible you should replace the reciever drier 'the little cylinder on the left hand side nex to the air box' as well

now i dont know how much one ( still waiting on call back)is but you should only get a new one so it all works good

if you can get hold of both of them they really arent that hard to fit just time consuming but its a good money saver for you cos the air con bloke only has to vac it down and regas it

all you need is a new orings for the hose fittings and some sealant for them or oil them up

its as easy as that

pm me if you want some ideas on what could be wrong

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...