Jump to content
SAU Community

Mt Buller - Wrap Up

Al

By Al,
in Victoria

 Share

Recommended Posts

  • Replies 134
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Basti Grand Master

Basti

Posted
Posted
It's Mel again,

The photos are BRILLIANT!!! Basti you should look at doing professional photography, stunning work!!!

I particularly like the oyster and prawn sexing......

xoxoxoxoxoxoxoxoxoxoxoxoxxx

lol, im too lazy. all i've done recently is meets. need to do other subject matter, which is why i loved this cruise.

jossef, you are welcome to have another ride man, i've got a time to try and beat now.

sprinter666 Enthusiast

sprinter666

Posted
Posted

lol roman fair point i suppose on that 1 but damn was so hot the tar on the road was melting aswell as my tyres so meh!

and yep basti ill take another ride get a 2nd vid when u crack 10 min, next time u come for a run with me when i set my car up :P a year should be enough unless we do this again sooner <3

180Roman Proficient

180Roman

Posted
Posted

i was like damn, the downhill drop just took the rear too far.

i saw you guys were a fair distance away so i knew you had plenty of time to slow down

i don't think James saw me though and he was surprised why you would slow down that much around that corner

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • WMDC35
      Wheel Sizes & Offsets For Skylines

      By WMDC35 · Posted

      A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...