Jump to content
SAU Community

Sluggish In Low Revs

Mooney

By Mooney,
in Engines & Forced Induction

 Share

Recommended Posts

Goodwin Apprentice

Goodwin

Posted
Posted
Hey, i have a R32 with rb25 na. Seems to be sluggish in low revs, anything above 4000rpm and its good, what can i do can a different tune or anyone else experienced this and found a solution??

cheers

Welcome to Club N/A where no power off the line is just the beginning.

WYTSKY Veteran

WYTSKY

Posted
Posted

Do u have an aftermarket exhaust? if so, it may be too big and actually cause a lack of back pressure resulting in the car being extra sluggish in low revs until a higher velocity of exhaust gas flows out, where it would be better for it...

_bobo_ Mentor

_bobo_

Posted
Posted

oOoO rb20...even worst lol

shoulda atleast tried to get a rb25.

but yeah 2.5inches is max you should go on a n/a otherwise you'll end up loosing back pressure.

2.25-2.5 is optimal for best performance. with a decent muffler and have it made as straight as possible.

WESTWD Community Regular

WESTWD

Posted
Posted
is 2.5 inch exhaust system good for a na rb20de r32 gts?

on your car, i personally would of gone 2.25 as i think 2.5 is too big.

hahahhaah lol

no need to laugh at him man, he was just after some advice.

R34GTFOUR Mentor

R34GTFOUR

Posted
Posted
you could always give the CAS a good twist in the advanced direction. will make it pick up much quicker, but the engine won't last that long.

Premium fuel goes a long way, I've been running mine at full advance for years, not a problem. Even in the peak of summer, full load, doesn't even think about pinging.

Definitely give that CAS a little twist, free HP imo.

mad082 Grand Master

mad082

Posted
Posted

if you are able to run full advance without pinging (unless you are running c16) then i wouldn't be suprised if your timing belt is 1 tooth out. or you just don't know what pinging sounds like. but then again the ecu is probably knocking 15 degrees of timing out because it is hearing the knock, so you could probably back your timing off a bit and not lose any power.

iseekool Veteran

iseekool

Posted
Posted
wtf i have a rb25 in mine, i have full exhaust system 2.5" with hi flow cat. worked diff and gearbox. adjustable fuel reg and gay ass pod filter. was thinking about extractors and chip it and give it a more aggresive tune

Run a few tanks of 98 fuel.

Remove any excess weight (stuff in the boot) - I'm guilty of having too much stuff there :rolleyes:

Check your tire pressures.

Clean your throttle body - you will be surprised how dirty it gets.

Try putting the pod in an enclosure or go back to a stock airbox and panel filter. You could be getting too much heat on the intake side of things.

Also are you running fairly wide tires and/or air-con? This causes alot of drag (resistance).

R34 -_- Community Regular

R34 -_-

Posted
Posted (edited)

"Premium fuel goes a long way, I've been running mine at full advance for years, not a problem. Even in the peak of summer, full load, doesn't even think about pinging.

Definitely give that CAS a little twist, free HP imo."

how do you do that?

Edited by R34 -_-
mad082 Grand Master

mad082

Posted
Posted

the CAS is located on the front of the engine. it is a round thing with i think 3 bolts located at even intervals around the outside. each bolt will be in an ovalised slot allowing movement of the CAS.

this should only be done with a timing light and having locked the ecu into timing mode first. this way you can monitor how much you have altered the timing. if you go too far and get pinging/detonation/knock and don't realise it, it can result in engine damage. also make a mark on where the timing was before you started so you know how much you have moved it if you want to back it off a bit.

R34GTFOUR Mentor

R34GTFOUR

Posted
Posted
if you are able to run full advance without pinging (unless you are running c16) then i wouldn't be suprised if your timing belt is 1 tooth out. or you just don't know what pinging sounds like. but then again the ecu is probably knocking 15 degrees of timing out because it is hearing the knock, so you could probably back your timing off a bit and not lose any power.

The belt hasn't been changed so it's not a tooth out and my brothers r33 gts had his on full advance aswell for years (when it was na). I know what det sounds like, she ain't pinging. Also when the stock ecu hears det and takes out 15 degrees of timing all of a sudden its noticeable, which it definitely isnt doing.

Not suggesting every just go and smash timing as much timing into theirs as possible, but for mine and my brothers, full advance worked a treat.

Ultimategtr Proficient

Ultimategtr

Posted
Posted

You cant hear an engine pinging, unless its pinging REALLY bad. Every engine is different. If you were to play with the timing, then you really need it up on a dyno to make sure its not pinging at all.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...