Jump to content
SAU Community

Recommended Posts

You may have some issues although nobody could tell me what the difference is between the ARX and RS suspension.

I suspect the BC coilovers I bought may have been for the ARX as the rears were nothing like what I needed, but I never checked, I just modified them.

A friend has just bought an ARX (GOLD LIKE YOURS) and has been speaking to Just Jap as I believe they are having some made that will be available quite soon.

I will try to get some more specific details for you.

Cheers

Andy

I was recently speaking to a guy selling BC coilovers on Ebay, runs his business out of New Zealand. Told him of the issues scotty had with them, he made enquiries to BC, apparrently, they have updated the NM35 kit (sept or so) to correct the issues. He was witing for updated parts for his kits at the time. So presumably, any kit ordered now, would be correct.

Hope this helps, Dale

Thanks guys I've been looking on eBay as well and seen the same things but this guy in new Zealand is not responding to my emails and waiting for an answer back for tenabe ones guess I ll

have to just wait and see what happens

thanks again guys

Thanks guys I've been looking on eBay as well and seen the same things but this guy in new Zealand is not responding to my emails and waiting for an answer back for tenabe ones guess I ll

have to just wait and see what happens

thanks again guys

Be careful which set if you buy for an ARX.

Yes Tanabe NF are adjustible... from -37mm to -78mm front and -38mm to -73mm rear WHEN FITTED TO AN RS, which means that on an ARX, you will be 77mm lower at the front from stock ride height when the Tanabe's are fully wound out!!

Maybe look for Bilstein or Nismo dampers and add a set of springs that are suitable for ARX.

Edited by iamhe77
Be careful which set if you buy for an ARX.

Yes Tanabe NF are adjustible... from -37mm to -78mm front and -38mm to -73mm rear WHEN FITTED TO AN RS, which means that on an ARX, you will be 77mm lower at the front from stock ride height when the Tanabe's are fully wound out!!

Maybe look for Bilstein or Nismo dampers and add a set of springs that are suitable for ARX.

do u think they will fit straight on without any mods

do u think they will fit straight on without any mods

Do not know for sure.

I can't imagine that the setup would be any different, but you have to remember that the ARX is 40mm higher from factory than the RS/RX.

Can you trial fit?

They're not technically coil overs on the rear of an M35 as the springs are separate from the shocks. So only the front is true coil over and that's as per standard.

Cheers

Gary

I think most of us are aware of the old "coilover" chestnut.

Given your expertise in the industry, would you happen to have a suspension solution for the original question (also for the RS/RX owners)?

There's a few people (myself included) who would welcome a local solution rather than resorting to importing parts ourselves...

Cheers, Dale

I think most of us are aware of the old "coilover" chestnut.

Given your expertise in the industry, would you happen to have a suspension solution for the original question (also for the RS/RX owners)?

There's a few people (myself included) who would welcome a local solution rather than resorting to importing parts ourselves...

Cheers, Dale

I second that motion local is easiest way

but I'm leaning towards resetting the springs any positive or negative thoughts on this way I've been td that u get the same ride comfort as factory what do u guys think

cheers Damon

I had a set of Bilsteins fitted to the ARX but kept the original springs for ride height (wanted to keep the stock look plus find the tailgate is fairly low already). This generally fixed the washy ride but it now crashes over the slightest depression in the road. I guess that the softish stock springs are not matched to the stiff Billsteins.

Currently waiting to get a set of ARX height Pedders springs made thorugh Ben at Northshore. Apparently 30% stiffer springs.

The stiffer springs should also help cornering - perhaps what it will finally need is an adjustable set of sway bars like Andy has done.

I second that motion local is easiest way

but I'm leaning towards resetting the springs any positive or negative thoughts on this way I've been td that u get the same ride comfort as factory what do u guys think

cheers Damon

the ride with the the Lowered Bilstein springs and sway bars is definatley firmer and can crash over some bumps but mind you with the stock setup the car was leaping over the road through the same pot holes. Also a big factor will be the tires you have on your car. the stiffness of the side wall is noticeable.

I guess for me the real test was from the seat of the pants of my wife. She thinks the ride is very good and has no problem with the stiffness of the set up and she is definable not into performance cars at all.

And best of all,, I love it. :)

On the topic of coilovers/suspension,

i have the tein kit on my car, it gets a little bouncy in the rear end still.. what do i do to fix this problem?

What kind of adjustment to they have? none? Height? Height & damper?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...