Jump to content
SAU Community

Recommended Posts

Maybe it should but it doesn't. Only single piston calipers up front.

I had heard about single piston calipers on 32's and am yet to see one. This confirms it.

If you're going 4 piston calipers keep an eye out for R33 gtst brakes. They bolt straight up and are 296mm not 280mm and often about the same price.

I had heard about single piston calipers on 32's and am yet to see one. This confirms it.

If you're going 4 piston calipers keep an eye out for R33 gtst brakes. They bolt straight up and are 296mm not 280mm and often about the same price.

You are right about the gtst with single pistons and 5 stud I didnt belive it until my mate brought on with them on it. and yes its a factory turbo not an na convertion

OK, I had a go at swapping the brakes and I ran into a couple problems. The one that is worrying me is that the S14 rotors are too thick; they rub against the dust shield thingo. Will I be able to use the thinner Skyline rotors safely or do I need to considder modifying the dust shield?

The other problem was that the banjo bolts from the Skyline were too long for the new calipers but I'll just get some shorter ones.

The S14 calipers do not use banjos. They use a flare fitting. You can buy them from any brake shop.

Just cut as much of the dust shield off as you need. Most of us here remove them completely. Depends how much street driving you plan on doing I guess.

It's a non-mspec GTS-T, I've got one too, 5 stud with the puny gts brakes... how are you connecting the calipers (hard-lines, flexis, etc?) as I'm doing the same upgrade in a while and it's always good to hear from someone who's done it already..

Sam

Yeah but I've heard of early gtsT's that had em too.

GTScotT's R32 had single pistons on it, it was a factory turbo too and 5 stud. (im not GTScotT)

also had rear brakes that we just couldnt match to anything, pads off some rarity model silvia and 5 stud rotors... go figure...

for conversion use the hard and soft line from the caliper right up to where it meets the chassis rail. the outlet on the chassis rail is the same yet AFAIK the single pots use a one peice rubber line, so you will need the complete 4 pot line caliper to rail.

Glad I came across this thread , Ive got a R32 GTE w/turbo conversion an 4 stud . Was jus gonna fit standard 4 pots pots but if i can fit 33gtst would be beta , any tips tricks or other info i should know . Also car is factory non-hicas which i wanna keep , any help appreciated

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...