Jump to content
SAU Community

Recommended Posts

Hi Stuart,

I'm using the Nulon 10W/40 for the motor and Nulon for the gearbox. The gearbox one is for Matic J(As well as others). Diff oil should be the same as an R34 GTR me thinks.

You need about 5lt's for the motor and about 8lt's for a fully drained gearbox.

cheers

so Matic J Synthetic for the Auto and transfer, 75w90 GL4 front diff and 80w90 LSD GL5 for th rear diff.....

This sound OK?

Transfer case is same atf as gearbox and steering. Get a 20L drum as gearbox will take about 14L - you need to pump it out via the cooler pipes to get it all.
  • 4 months later...

Any updates on how this went?

Looking to do the same. Thinking of http://www.nulon.com.au/products/Full_Synt...smission_Fluid/ in the auto and Red Line 'Lightweight Shockproof' for the diffs.

Comments?

Any updates on how this went?

Looking to do the same. Thinking of http://www.nulon.com.au/products/Full_Synt...smission_Fluid/ in the auto and Red Line 'Lightweight Shockproof' for the diffs.

Comments?

Exactly what I have in my car.

No complaints whatsoever :happy:

Good to hear.

So how much do I need? Is the 20l comment above accurate?

How much of the Red Line?

Thanks

3 bottles of Redline Lightweight Shockproof will leave you with some left over. Get them from for damn good pricing :)

You will need around 8.3L of trans oil if filling from empty.... if flushing, Nissan use 10.5 on their machine.

As an aside, you can also use the Nulon trans fluid for the ATTESSA and power steering (Nissan use Matic D for these)

Edited by iamhe77
Good to hear.

So how much do I need? Is the 20l comment above accurate?

How much of the Red Line?

Thanks

On the gearbox without flushing it completely you will be hard pressed getting 5lt's of the old oil out even with twin after market transcoolers( :))....so 5lt's if your just want to change what's in there without flushing. If not I think it's about 7lt's or 8lt's plus a flush....IMO unless your oil is cooked I would not bother with a complete flush.

As for the diff's.....haven't done em yet so.....I guess someone else can answer that.

I had a 60% blocked radiator for a while, so I wouldn't rule out cooked.

Got details on the after market oil cooler? I'm noticing the gearbox seems to start hunting a little bit after getting heated up on a long highway climb. Wouldn't mind getting a bigger cooler in there if it isn't a huge expensive job.

I had a 60% blocked radiator for a while, so I wouldn't rule out cooked.

Got details on the after market oil cooler? I'm noticing the gearbox seems to start hunting a little bit after getting heated up on a long highway climb. Wouldn't mind getting a bigger cooler in there if it isn't a huge expensive job.

Any trans cooler will be of benefit.

Personally I am running a PWR "6-cylinder" unit and have mounted it on a bracket behind the grill as you can see below (obv without the grill).

IMG_2130r.jpg

There are plenty of cheap trans coolers. Just note that if you are using a 3/8" transmission hose, you will need to make sure of the connection to the radiator cooler as I believe they are slightly smaller than 3/8".

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...