Jump to content
SAU Community

Recommended Posts

  • Replies 521
  • Created
  • Last Reply

Top Posters In This Topic

Where's a decent place to get under bonnet grey matt paint for a BNR32 stadnard dark grey skyline?

I dont want ot fix outside scratches - want to touch up the engine bay before refitting the turbines

The underbonnet paint should be the same as the exterior. Give me the paint code and I can get a tube in from Japan.

Ken

Link to comment
https://www.sau.com.au/forums/topic/30197-darwin/page/12/#findComment-973529
Share on other sites

  • 2 weeks later...
he he , who owns the stocko red r33 gtst, that tryed to race me at the lights in the city last night about 11.00pm ?   was funny lol

Obviously wasnt me. I would have won. Chuckles. I hear you have a phone for sale but apparently it's a bit of a shitter! HAHAHAHAHAH

CUL8R

Ken

Link to comment
https://www.sau.com.au/forums/topic/30197-darwin/page/12/#findComment-986361
Share on other sites

hey ken baby ..... the forums are back online lol

 

oh oh  and nice tow bar mate, might get 1 myself to tow the jet ski 1 day !

Jetski, Manton Dam, BBQ, Suds - sounds like a cruise day to me!!

Just to let everyone know, my wife and I had a little baby girl yesterday at 4pm. Caitlin Sarah May weighed 7lb 10z. Both Lisa and Caitlin are doing really well.

CU

Ken

Link to comment
https://www.sau.com.au/forums/topic/30197-darwin/page/12/#findComment-990091
Share on other sites

  • 1 month later...
  • 1 month later...
Yea same Ken well done

I'll have to come see her some day

I talked to TPL about dump do you have the gaskets for both ends of the dump pipe as it would make it a whole lot easier to make, I'll get the price later but it shouldn't be much at all

Mate he should be able to take an outline of both ends, take some photos/measurements and make the pipe. I dont have a gasket or either end of the dump sorry.

Best of luck, what was his price btw??

Cheers m8,

Ken

Link to comment
https://www.sau.com.au/forums/topic/30197-darwin/page/12/#findComment-1087644
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...