Jump to content
SAU Community

Recommended Posts

no no you don't.

Hakosuka, V35, aus spec R31 in that order

the guys on that R31house video reckon the RB30S is a shitter lol

twin cam non turbos are for the gays

What about the Autech RB26DE R32? I think I'd take that over any other NA Skyline.

What about the Autech RB26DE R32? I think I'd take that over any other NA Skyline.

You'd take it over a KPGC10 GT-R?!?!?!?

A friend of mine owns this:

4021243833_c8fd242224_o.jpg

While its not a genuine GT-R, I'd still take that over any other NA Skyline bar a V35 (just for its modern mod cons).

You'd take it over a KPGC10 GT-R?!?!?!?

A friend of mine owns this:

4021243833_c8fd242224_o.jpg

While its not a genuine GT-R, I'd still take that over any other NA Skyline bar a V35 (just for its modern mod cons).

Yeah, I would. The automatic transmission would irritate me, but IMO that car does nothing for me, it just looks old, and there are much better looking cars from that era.

ive seen one and touched one, havent had a chance to drive one.. old cars are so much better imho.. u get that direct feel/interaction with the old cars that u just dont get the same feeling due to power steering + safety aides.

Love the hakasukas(sp?) u just gotta make sure u have those ITBs growling loudly =)

Love the hakasukas(sp?) u just gotta make sure u have those ITBs growling loudly =)

Carbs, you mean carbs. Hakosuka's have 3 side draft carburetors. :)

My pick Hakosuka number one, and my own ITB R32 second! :D

picture001z.jpg

Edited by screamin'

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...