Jump to content
SAU Community

Recommended Posts

well was out at keilor road tonight having coffee with the car parked directly out the front so i could stare at it in aw (lol) and was enjoying myself when low and behold some fag in an XF XR8 ute was parking in the spot in front of my car

i said to my company at the time i bet he hits my car

so we watch

he backs up, bit closer, closer, closer, by then i KNEW it was over and sure enough, BUMP, alarm goes off, i get up walk out to see hit tow ball had dented the **** outta my cooler, luckily enough for me it didnt pierce it so the cars still driveable but it will need a new front mount, i just hope he isnt a ball breaker and will just accept fault and i can get the new front mount on asap so the car is as sexy as it deserves to be :P

/end rant

Link to comment
https://www.sau.com.au/forums/topic/30311-time-for-my-3rd-front-mount/
Share on other sites

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

nah its just the intercooler, the tow ball on his ghey ute was all that touched it, but im going to say he also scratched the bar coz the other day i hit a gutter when parking whilst perving on a hot chick... lol so ill get the bar re-sprayed too :P

tell me about it danny hehe

thanks guys for the support, its times like these i really want to justgive up, all the time i spend getting my car perfect and shit like this happens in a flash right before my eyes, but spose could have been worse, could have parked where i cant see the car and the guy just leaves it and i have to pay for it myself

i wouldnt give a crap if a girl was there or not i would of ripped his ****ing head off hahaha

soft cawk! :P

It's a bit different when your trying to get your end in :headspin:

HAHAHAHAHAHA!!!!

did you end up getting his license No. like i told ya ????

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...