Jump to content
SAU Community

Recommended Posts

hey guys i wanna try build my first computer and i want to make it an elite gaming machine all i need is just a set up if yous could help me with eg. a list of awsome parts that are gunna be compatible..im bit behind with the latest gaming parts thanks.

Link to comment
https://www.sau.com.au/forums/topic/303876-building-a-elite-gaming-machine/
Share on other sites

this thread is going to go for a while. Also have a look at some of the PC build threads in here for some good advice and some builds that are prob what you are after.

Some good online stores already have decent PC's made at a good price

www.netplus.com.au

www.scorptec.com.au (i have not used em so not sure)

www.ple.com.au

www.pccasegear.com.au (not pre built systems but if you want to make one my purchases from there have always resulted in me being a very happy customer)

i7 920 D0 stepping - $350

GA-EX58-UD3R - $250

Corsair HX750 - $250

ATi 5870 - $500

G.Skill or Kingston DDR3 PC16000 - $250

Lian Li Armorsuit PC-P50 - $250

Prolimatech Megahalems Rev. B - $90 (you'll need a fan as well $20, Scythe Slipstream 1900)

~$1950

With that setup, overclocked , would be the current PC to put together if i were to build a solid gaming box that won't need upgrading within the next 2 years.

Games will run on full settings, full AA, the works. So the will look as good as they can :blink:

Honestly id say get a 24", BenQ ones are like $200-$220.

ok thanks for that ash, where do u buy your parts from? aparently theres a really cheap place in boxhill just behind carrington st. are benq monitors any good? i was thinking mayb a samsung or hp

and 25Gtt im not after a already built pc, i wanna build my own...just as a project..just so i can learn.

www.staticice.com.au

Check pricing there, go to whoever is cheapest.

But also send places a full list and see if they will discount for you, you never know, which would save you going to 4 different once.

PCCG & MSY usually don't discount, but then generally they are the cheapest from what i've found.

Centrecom & Scorptec's pricing is higher than MSY/PCCG usually.

Nothing wrong with BenQ - im using a 24" one happily for over 12 months now.

The other monitors are just overpriced. At the end of the day they are all a "TN" panel, so $240 is all you should spend as there are always monitors "on special"

Unless you are going a IPS/S-IPS panel but then for a 24" you are looking @ $800. If you aren't doing graphic design, where colours are SUPER important, they aren't worth the coin :D

Personally, i'd be snapping this up while it's on sale :blink:

http://www.pccasegear.com/index.php?main_p...oducts_id=12310

You can't seem to get 24" in 16:10 (better for gaming) anymore, i think i got the last of the 16:10 24" ones on the market - but still 16:9 is perfectly fine

I have a Samsung 2443BW which is 16:10 and is still listed on PCCG, but they are phasing out.

ATi 5870 - $500

Honestly id say get a 24", BenQ ones are like $200-$220.

Yeah, if going single screen a 24" or 1920x1200 (/1080) res should be your minimum for that GPU. Otherwise the ATi HD5850 will more than suffice.

^ Ah, true that. But double the price of the BenQ - but nowhere near double the quality!

I also agree, it'll be 1900/1200(1080) @ a min, depending on monitor choice that might be the highest res.

Even a 5850 would perform very nicely on such a monitor, guess depends if you want upgrade again in 12 months or not.

If the budget is tight and you want to save $120 then a 5850 would without a doubt still perform excellent for the task at hand.

GPU's are a long way ahead of games at present so there is some nice headroom with most new fab cards.

I'd go R31Nismoid's deal of box, that's dirt cheap for what it is.

I just bought a dual core 2.93 (E7500) with 4 g of ram, 9800GT video card, 1tb hdd etc for about $700, and it seems to play my games quite nicely. I usually buy one of something like this per year, and retire the older box as some form of movie server, web server, etc.

  • 2 weeks later...
PCCG & MSY usually don't discount, but then generally they are the cheapest from what i've found.

Centrecom & Scorptec's pricing is higher than MSY/PCCG usually.

That said i have often found centrecom will match msy prices at the counter if you ask...Which is handy for me cause centrecom is close msy is a drive :D

^^ A PC for the fool :)

Over spec'd parts, that offer no better performance than cheaper ones... he who pays for that, be a sucker!

That said i have often found centrecom will match msy prices at the counter if you ask...Which is handy for me cause centrecom is close msy is a drive :thumbsup:

Ye they usually match, friend of mine goes there and always gets matched.

Comes down to who is closer :D

  • 2 weeks later...

whirpool.net has alot of pc configuration and they usually update it to budget and what you will do with it.

but when you buy your lcd make sure it fits your table. i had to use a different table because my old one broke. and i have a 24 inch and it too big for this smaller table so it has to sit kind of sidways to fit on the table.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...