Jump to content
SAU Community

Attesa Et-s On R34 Gtt?

savvas_greece
 Share

Recommended Posts

savvas_greece Newbie

savvas_greece

Posted
Posted

hello everyone,i am Savvas i'm from greece and i am going to buy an r34 gtt (rwd) and i want to know if i can put an attesa et-s system on it...??? if this helps, i will install an rb26dett on it.... i ask you because you are one of the biggest forums for nissan skylines and i belive that know almost everything about these cars....any help is accepted...

Link to comment
https://www.sau.com.au/forums/topic/304338-attesa-et-s-on-r34-gtt/
Share on other sites
savvas_greece Newbie

savvas_greece

Posted
  • Author
Posted
you may need to clarify your post a little more OP. Do you mean you would like to put the whole 4wd drivetrain from a GTR in or as blind elk has read it and you just want the electronic system which would do nothing

sorry...my mistake....i want to put the hole awd drivetrain and the attesa....

savvas_greece Newbie

savvas_greece

Posted
  • Author
Posted
hey champ if you want 4wheel drive you should just buy a GTR(4wd) instead of buying a GTT(2wd),,, it be alot WISER and probably cheeper. do yourself a bit of research!!! :)

i prefer this gtt because it is lhd (left hand drive) and here in my country people use lhd cars.....does anybody else knows if this is possible?? :rofl:

dkbcleaner Proficient

dkbcleaner

Posted
Posted

Anything is possible if you have the money.

Have you looked into converting a gtr into lhd. I'm sure it would be much easier to do that and probably cheaper and more reliable too. Not to mention all the extra good stuff and looks a gtr has over a gtt.

blind_elk Grand Master

blind_elk

Posted
Posted
sorry...my mistake....i want to put the hole awd drivetrain and the attesa....
Fitting ATTESA AWD is not the simple matter of fitting the mechanical components. ATTESSA relies on a heap of hydraulics and electronics to work. It is the general consensus of many members here that it is simply not worth the time / expense / heartache.
Craig SLO33 Enthusiast

Craig SLO33

Posted
Posted
hello everyone,i am Savvas i'm from greece and i am going to buy an r34 gtt (rwd) and i want to know if i can put an attesa et-s system on it...??? if this helps, i will install an rb26dett on it.... i ask you because you are one of the biggest forums for nissan skylines and i belive that know almost everything about these cars....any help is accepted...

you can do anything if u really want 2...I know that a Workshop in the states (usa) has installed all of the GTR running gear into a Silvia..so now they have whats essentially an all wheel drive Silvia, thats pretty much what ur talking about..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • GTSBoy
      R34 Handbrake light saying ON and intermittently flashing

      By GTSBoy · Posted

      Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • Duncan
      R34 Handbrake light saying ON and intermittently flashing

      By Duncan · Posted

      ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...