Jump to content
SAU Community

Recommended Posts

Help me get my shed back in order. Need to fund a new wakeboard!

HKS VPC. Come with everything. Use this to remove your AFM's on your gtr and still run std or pfc ecu $400

Set of front guard liners and front under tray. Has front brake ducts and I won't seperate. $250 Getting very rare!

RB26DETT oil pump $80

Harmonic balancer $50

R32 GTR fuel pump in cradle $80 each. I have two of these.

Twin Turbo pipe - From turbo's to intercooler pipe $100

R32 3inch exhaust with seperate de-cat pipe. Has centre muffler, no rear muffler, just straight throught to out back $100

Standard R32gtst exhaust I used to clear epa on gtr $100

R32 GTR metal fuel cap $30

R32 GTR ABS mater cylinder $100

R32 GTR G-Sensors $100 Qty 2

All ECU's below suit std injectors and turbos

2x Mines ECU's for R32 GTR $100 each

Blitz ECU for R32 GTR $100

New R/H sill panel $100 Suit GTR/GTST

R/H tail light $30

R/H mirror $25

R33 GTR lowered rear springs for std style shocks $50 sits very nice

Tein stiff springs. Perfect for drift. $30

Melbourne Can post. Please no time wasters. You know who you are!

This will all end up on ebay if its still around in a few weeks so I thought I'd give the SAU crew first dibs.

Looking for a std boost solenoid, flywheel and clutch and intercooler for R32 GTR.

Link to comment
https://www.sau.com.au/forums/topic/306748-large-range-r32-gtr-gtst-parts/
Share on other sites

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

De-cat pipe is to suit the exhaust. Prob won't go between a std style front pipe and exhaust. Might be a bit long. Its just a bit of pipe with 2 flanges welded on. No need for pick.

Re- clutch/flywheel. Might be interested. Depends on price. Don't need it to bad but its a bit of a pain when I have to take off with my boat on when stopped on hills or at the ramp with the tripple plate in it. Pm me with a price. It'll just mean I can't give the car to much of a hard time as I've seen a few std flywheels explode.

There for std injectors with the normal mods - exhaust and a bit of boost. I have run all of these and they run fine. Don't have any dyno results for them compared to stock but I did look at the fuel and timing map on them and it was std bottom end of map with a fair bit of timing and fuel taken out of the top where you don't want it after adding a little boost.

How much you wanna spend on clutch an flywheel as I have a exedy heavy duty cushion button clutch and STD flywheel sitting around...

Feel free to contact me On 0419797023 cheers Tim

Wouldn't spend much as a flywheel is worth nothing as there the same as 20's I think plus they explode and a clutch is only around $250 new. Pm me with what you want for it.

Got One pm replied.

There just std looking ecu's with Mines and Blitz ecu stickers on them. They're definantely chipped.

$100 is cheap man..but once they are chipped, (normally done in japan) they cannot be played with at all... had one in my GTR.... got rid of it with the engibe build... you wouldnt have front pipe for 32 GTR would ya?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...