Jump to content
SAU Community

Recommended Posts

Picked up a fresh import 34 GTT last week, now its in townsville, just wondering if anyone knows if the crushing humidity here (generally 75 to 95% all the time) has an effect on the performance or fuel efficiency? If so to what extent? I assume the car is made for cooler and less humid japan, hence the small intercooler so if anyone can help please do. Thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/308138-high-humidity-vs-turbo/
Share on other sites

yeah its common knowledge that temperature would affect performance, humidity on the other hand i am unsure

just use good fuel and ensure the engine is in good working order

the intercooler is not on the factory setup to suit the climate, it is there to reduce heat from the intake charge from the turbocharger. the intercooler is only as a good as the ambient air temperature

yeah its common knowledge that temperature would affect performance, humidity on the other hand i am unsure

just use good fuel and ensure the engine is in good working order

the intercooler is not on the factory setup to suit the climate, it is there to reduce heat from the intake charge from the turbocharger. the intercooler is only as a good as the ambient air temperature

Yeah i know temp is an issue, but cant figure out the humidity, the air is so thick and heavy, i know its not the same but breathing while running here is so much harder than in low humidity i thought maybe it could have a similar effect on a car.

it should be ok, i mean there isn't much you can do it about - ie you can't negate humidity

Yeah true,but i noticed in 1/4 mile time cards humidity is listed as a factor alongside temp, wind etc.

Maybe slightly worse for wind resistance or something, im out of ideas haha.

Thats why I live in Tassie. It's cold ALL the time! ha ha ha. Good crisp air is awsome for power production and throttle response.

It would be hard to know what effects humidity (if any) would have in such a warm climate.

If your worried about intake temps and humidity, throw the car on a chassis dyno in summer and give it a good work out. Then log the coolant, oil and air intake temps as well as afr's/detonation.

If your so inclined- install a larger intercooler and oil cooler with a thermostat. Also if the car is auto, invest in a trans cooler if your going to give the car a hard time.

Edited by XRATED
Thats why I live in Tassie. It's cold ALL the time! ha ha ha. Good crisp air is awsome for power production and throttle response.

If your worried about intake temps and humidity, throw the car on a chassis dyno in summer and give it a good work out. Then log the coolant, oil and air intake temps as well as afr's/detonation.

If your so inclined- install a larger intercooler and oil cooler with a thermostat.

May try that actually, will have to wait until the end of the wet season for a cool day with lower humidity but.Yeah bigger intercooler is on the to do list lol

May try that actually, will have to wait until the end of the wet season for a cool day with lower humidity but.Yeah bigger intercooler is on the to do list lol

Try that.... moving to Tassie, Good plann! ha ha ha.

If your worried about the heat/humidity throw the car on the dyno on the hottest- most humid day you can...

Yeah I know... ha ha ha

I was stationed there for a while. PT on mondays after a sunday session is not fun in 45deg heat and 95% humidity.

Tell me about it, i still have 2 1/2 years here haha, thats what made me think about the car, it affected my performace so much i thought maybe the principal would transfer over?call me crazy

The effect of Humidity on engine performance is not worth considering.

Temperature and air pressure are the main factors that effect air density, which in turn will dictate engine performance. Every degree of temperature increase is equivalent to going up in elevation by 120 feet. A drop in pressure by 1 HPa has the effect of going up in elevation by 30 feet.

A turbo charged car is going to be less effected by pressure changes than a naturally aspirated one, because air is being forced into the manifold at greater than ambient. Temperature is the main thing that will reduce a turbo charged cars performance.

In Aviation we doing not factor Humidity into performance calculations because it is negligible.

The effect of Humidity on engine performance is not worth considering.

Temperature and air pressure are the main factors that effect air density, which in turn will dictate engine performance. Every degree of temperature increase is equivalent to going up in elevation by 120 feet. A drop in pressure by 1 HPa has the effect of going up in elevation by 30 feet.

A turbo charged car is going to be less effected by pressure changes than a naturally aspirated one, because air is being forced into the manifold at greater than ambient. Temperature is the main thing that will reduce a turbo charged cars performance.

In Aviation we doing not factor Humidity into performance calculations because it is negligible.

Sounds pretty definitive, thanks mate.

Humidity does have an effect on any engine.

Those water parrticles are taking up space, oxygen space. The greater the humidity, the less air your engine has to breathe.

Why do you think a dyno needs input from humidty, inlet air temp, etc etc?

It's all compensated for in the dyno's computer package.

Give Trent or someone who does a lot of tuning a PM.

Humidity does have an effect on any engine.

Those water parrticles are taking up space, oxygen space. The greater the humidity, the less air your engine has to breathe.

Why do you think a dyno needs input from humidty, inlet air temp, etc etc?

It's all compensated for in the dyno's computer package.

Give Trent or someone who does a lot of tuning a PM.

Those are the lines i was thinking along.Who is trent?

Yeah the humidity up here is very annoying, walk outside for five minutes and feels like you have walked into a shower. I notice a huge difference from day time to night time driving here, mixture of humidity and air temperature definetely has a very noticable effect.

Edited by PM-R33
Yeah the humidity up here is very annoying, walk outside for five minutes and feels like you have walked into a shower. I notice a huge difference from day time to night time driving here, mixture of humidity and air temperature definetely has a very noticable effect.

Yeah i notice that too, but night here is still hot and humid like a rainy hot day anywhere else hey.now its crazy with all this rain its just getting worse.

Yeah its not the best place for enjoying a modified car. Hopefully if all goes through i should have my car out doing circuit work this year. Really worried about water and oil temps going throgh the roof though. Most of my "spirited driving" is done at night time where i never have an issue with temps, day time however is a bit of an unknown.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...