Jump to content
SAU Community

Recommended Posts

  • Replies 97
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

-6 only has one size, they either have it or they dont.

argh -6 is the size yes i know this. but the male adaptor that screws into the block has to be the correct size example. m14x1.5 to fit 90 degree speedflow barbed fitting in -6

ive got a catalouge here and the guy on phone thinks its a m12x1.5 but stao thinks its a m18x1.5 then another person rkns m14x1.5 lol.. its not just hey can i have a -6 male to male adaptor.. gotta know what size thread to suit.. :blush: well thats how i see it.. everything in this book has thread size then u pick ur stock range to suit etc -4 -6 -8 -10 blah blah... still need the thread size to screw into the block.

I see wot u mean titan. 920-6 looks like the one i would need?

see for the turbo gt3076 water lines i need a 732-06 which is m14x1.5 -6

the 920-6 doesnt give me a metric thread so id be taking a guess saying it will fit?

Edited by l0WRB
  • 2 weeks later...

Turbo has been fitted and wastegate has been welded off the stock manifold

boost set at 18psi and it made 290rwkw basically on fullboost at around 4100rpm and it just turns the tyres hahaha made near 500nm torque

will post up dyno sheet soon

Mate, that has honestly ended up an impressive setup!

It looks great and the improvement in power delivery is worlds better. That gate looks tops too, big ups mate.

Keen to hear your experience on driving it :P

Looks like every thing's running pretty good. It is smaller but the right turbo for your application.

Also I would like to address. The secondary power and torque curve is not from our 3582. It is our 3582 CHRA in a unknow turbine housing by high flowing. It have performed differently in our .82 turbine housing.

Would you have a copy of boost curve by any chance? I like to compare it with the sleeve bearing version of it in some atr43s

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...