Jump to content
SAU Community

Recommended Posts

-access the CONSULT port, bottom right side of dash behind flip down door.

-ignition OFF

-ground bottom middle terminal using a wire.

-ignition ON

-observe flashes (also beeps) of ABS light

-it will start with '12', (1 long flash then 2 short.)

-it will then flash the fault codes.

-to clear the codes, whilst in this diagnostic mode, disconnect the grounded terminal, then ground it 3 or more times, for at least 2 sec, within 12.5 sec. restart diagnostic mode to check if thwey have been cleared. May take a few attempts before the codes clear.

21 Front right wheel sensor (open circuit)

22 Front right wheel sensor (short - circuit)

25 Front left wheel sensor (open circuit)

26 Front left wheel sensor (short circuit)

31 Rear right wheel sensor (short circuit)

32 Rear left wheel sensor (short circuit)

35 Rear left whel sensor (open circuit)

36 Rear left whell sensor (short circuit)

41 Front right outlet solenoid valve and circuit

42 Front right inlet solenoid valve and circuit

45 Front left outlet solenoid valve and circuit

46 Front left inlet solenoid valve and circuit

55 Rear outlet solenoid valve and circuit

56 Rear inlet solenoid valve and circuit

57 Battery voltage

61 ABS actuator motor and motor relay circuit

63 ABS acutuator relay circuit

64 FR & RR G sensor 1

65 FR & RR G sensor 2

66 FR & RR sensor 1 or 2

68 G sensor voltage

69 Side G sensor voltage

71 ATTESA E_TS PRO/ABS control unit and circuit

72 Throttle position sensor

73,74 E-TS/LSD actuator motor

76,77 Pressure switch

78 Air bleed switch

79 Oil level switch

91,92,93 E-TS solenoid

94,95,96 E-TS fail safe solenoid

97,98,99 LSD solenoid

Hey Mat, welcome to SAU, and to the Stagea section of the forums.

First things first, do a quick search for your problem in this section of the forums, and you should be at least be able to find a link with info for getting ECU codes. Once you do that, see if anything matches what's previously posted. If you can't find any details about what corresponds to the codes given, post the details on here and see if anyone else can help!

yeah ive searched the forums and everything ive tried hasnt worked.

ive tried the consult port and it doesnt stop flashing i counted 102 before i gave up.

i wouldnt think a slight tire differnce would affect the system.

there is a differnce by 2.06% but wouldnt think that would be enough to affect the system??

or am i wrong?

yeah ive searched the forums and everything ive tried hasnt worked.

ive tried the consult port and it doesnt stop flashing i counted 102 before i gave up.

i wouldnt think a slight tire differnce would affect the system.

there is a differnce by 2.06% but wouldnt think that would be enough to affect the system??

or am i wrong?

From the million times this has come up on this forum, I'd say stick to the same size rims/tyres for all 4 and you wont have any problems. The ATTESA system apparently doesn't like differing rolling diameter front vs rear OR differing tyre width...it allows enough leeway for uneven tyre wear, but thats about it.

yeah ive searched the forums and everything ive tried hasnt worked.

ive tried the consult port and it doesnt stop flashing i counted 102 before i gave up.

i wouldnt think a slight tire differnce would affect the system.

there is a differnce by 2.06% but wouldnt think that would be enough to affect the system??

or am i wrong?

flat(er) tyres also cause the jerkyness and even bald vs new tyres

see if you can throw on some rims from a different car which are all identical

  • 1 month later...

yeah i thought the same thing. ive tried the consult port and i even have a cable but i dont get any fault codes,

the fault clears as soon as i turn the car off, and the light wont come back on untill i drive about 20-30km's

ive noticed a small amount of fluid araound the bottle in the boot so ill drain it and check all the lines and replace the fluid.

  • 4 weeks later...

before you do anything make sure the fluid level in the ATTESA reservoir is between full and empty, and that you don't have any leaks so that the system can pressurise.

  • 6 months later...
  • 6 months later...
  • 4 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A 1.5 way is a 2 way. It is just a 2 way with a less aggressive ramp on overrun.
    • The ABS and/or TCS being missing/broken will not cause the engine to misbehave. It just casues CEL to come on and annoy you. The CEL is useless if it is always on, so you have to do the things you have to do to get rid of it, so it can be useful. Being a Stag ECU, then yes, it will not expect TCS to be present. But it will expect ABS to be present and working. You will need to either make the ABS CU talk to the ECU (don't ask me what that will take on an NA R34), and make sure the hardware is working....or, you just need to blank it out in Nistune. Do not persist with the stock ECU. You will just have problems. Gte it Nistuned. Start from there. DO YOU HAVE A BOOST SENSOR? The ECU's boost sensor that it. It is connected to the loom at the rear of the coil cover. Usually rides on the firewall on an R34, but is usually bolted down to a bracket along with all the other crap at the back of the coil cover when a Neo is dropped into another car. If you do not have it, the ECU will shit the bed. So, do you have one?
    • So sadly the fuel pump etc was not it. The pump and filter is new and it is still cutting around 4000 rpm. A read something about ABS/TCS (engine is from stagea and ECU too so no TCS) and i dont know for 100% that my car has ABS. It has ABS "cube" in engine bay but i dont think it works(or at least from my braking experience). Can be something like that?  I will be driving the car next week to Nistune tuner to properly see what is wrong...  
    • the Tomei LSD fluid with lsd kit. frustrated that it was shaking the car to crap and affecting everything else negatively, I pulled the diff last night, and removed the lsd carrier, could not find anything wrong, however it seem to be 100 locked up acceleration, and deacceleration, wondering if they sent me a 2 way not a 1.5??  either way I installed the stock open carrier back in place. test drove everything smooth as butter again. no shake, shutter, random, what felt like clutch slip and grab or drive shaft play, etc. something differently wrong in side the lsd. I might bother taking it apart (if possible) to figure out what's going on inside this carrier, as bought too long ago to return.  only draw back is its back to a one wheel wonder.
×
×
  • Create New...