Jump to content
SAU Community

Recommended Posts

Rear guards are already rolled. Wouldn't they need to be flared though? My fronts hit the guard like a mofo and they're only sticking out 6mm.

15mm spacers in the rear would mean 10+mm out of the guard.

get the 10mm spacers then. you should be able to flex the metal 5mm pretty easily. I got an extra 10mm out of my ceffy when I rolled it. Didn't need a respray.

just sell the wheels and start again if it's all too hard for you.

also helps if you stretch tyres. I tucked a 10.5" with 225's on the back of the cef. no way that would fit without stretched tyres.

your tyres are probably scraping on the front cos you're probably running Pat spec tyres.

47455_430007199299_618369299_5037820_5212260_n.jpg

nice... I don't see any hub locating rings on those wheels either. And you wanted to run 5mm spacers? oh dear.

46890_426792349299_618369299_4970314_4885725_n.jpg

notice rim isn't even visible cos the tyre's too big? if your wheel is tucked this is how it should be, but if your wheel is mexican then you need to stretch at the bare minimum to prevent it getting cut up every time you hit a bump.

compare this to mine:

3411414688_efc6a4ab30_b.jpg

see what you need to do if you're running flush or slightly pokey wheels?

Hmm... So fronts would be better with like a 205 yeah? And a bit of negative camber? Would that affect handling?

depends. if you like drag races only then it's bad. if you like cornering then it's good. if you like tyre longevity then GTFO.

more pressing issue would be to get some hub locating rings on those wheels. atm the only thing holding them in place are your lugs.

haha yeah, that's the other thing - if you go hub centric spacers then hole in the spacer need to match the hubs and the ring on the spacers need to match the wheels - or run hub rings as well as spacers

But did the rings match your hubs or your rims?

I bought ones to suit an MR2. So I guess?? 60.1 is the number I was told to order.

I really have no idea what I'm talking about, as you can guess.

Edited by jezza boii
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...