Jump to content
SAU Community

Recommended Posts

Hello :blink:

Im trying to figure out a styline route for my R34 4 door. Does anybody know (for certain) what the compatability is between the 2 door and 4 door chassis?

Are the wings/bonnet/front and rear bumper the same on both cars?

Link to comment
https://www.sau.com.au/forums/topic/311473-r34-4-door-vs-2-door-compatibility/
Share on other sites

front bar is the same, bonnet same

rear bar is not

wings? you mean front fenders? or side skirts?

- Front fenders the same - Pretty much everything up to the A pillar.

- Whole dash assembly the same.

- Front seats the same

- Front suspension, Rear suspension - the same (...but I've read somewhere - please don't quote me on this - stock front suspension on the sedan is slightly stiffer due to the extra weight when braking)

- Tail lights - different

- Boot - Different

- Rear bar - Different.

Eastbear have some nice coupe/GTR style bumpers and panels for the R34 4 door -> http://www.east-bear.co.jp/

  • Like 1
  • 1 month later...
To have the front bar bonnet off a gtr i beileve you have to replace the bonnet bar an fenders all in one hit.

Also the mounting points for the lights are different as far as I know, which mat suggest the fron uprights needs changing to do it all properly. Otherwise you can knock up brackets to fit the GT-R lights.

  • 2 weeks later...

i think you will find the front seats are different from 4 door to 2 door.

i purchased a set of front seat rails for a 34 gtt autotechnia brand i think they were, sign said 34 4 door compatible, tried fitting and works out they are only for 2 door version. rang mob who made them and they said the 4 and 2 door are different, and they don't make 4 door version. bolt holes at rear of seat are the difference.

I have a 2001 turbo sedan with the update bumper and wanna take it off to fit a non turbo early model bumper :(

Is there a difference between early model turbo and non turbo front bumpers?

Or are people refering to the non turbo as the standard type then the turbo as the nismo option type?

Attached picture's for reference, the black one to me is the standard bumper with the lip, the orange one the Nismo option bar, then you get the later model round type?

Oh and seats 2 door and 4 door are the same, but 2wd - 4wd are different.

post-11869-1274587009_thumb.jpg

post-11869-1274587020_thumb.jpg

Edited by msports180
i think you will find the front seats are different from 4 door to 2 door.

i purchased a set of front seat rails for a 34 gtt autotechnia brand i think they were, sign said 34 4 door compatible, tried fitting and works out they are only for 2 door version. rang mob who made them and they said the 4 and 2 door are different, and they don't make 4 door version. bolt holes at rear of seat are the difference.

Seats are the same. Could be the rails that are different lengths - as you will need to move the seats more for coupes for rear passenger access.

And there's no difference between early model and late model front bumper fitment?

I have a 2001 turbo sedan with the update bumper and wanna take it off to fit a non turbo early model bumper :(

If you are running the stock side mounted intercooler - I do NOT recommend putting a non-turbo bumper - reason being is that it needs the side vent.

If you have a front mount intercooler - the non-turbo bumper will be ok, but may require some modification.

If you intend on keeping the side mount intercooler - your options are limited to the GTT bumper or nismo bumper - or if you're really keen a GT-R bumper, which means you will need a new bonnet, side fenders etc.

Is there a difference between early model turbo and non turbo front bumpers?

Or are people refering to the non turbo as the standard type then the turbo as the nismo option type?

Attached picture's for reference, the black one to me is the standard bumper with the lip, the orange one the Nismo option bar, then you get the later model round type?

Oh and seats 2 door and 4 door are the same, but 2wd - 4wd are different.

Non turbo doesn't have the vent on the side for the intercooler etc. Seeing as I don't want that, that's the reason for going non turbo.

Does anyone know if the tailshafts are the same between 2 door manual gtt and 4 door auto gtt? I need the rear section changed on my 2 door as the center bearing has collapsed on the rear sectin of the two piece tailshaft and I have access to replace it with a 4 door auto shaft and bearing.

Here is a picture of the part in question...

PICT0009.JPG

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...