Jump to content
SAU Community

Recommended Posts

I am situated in Melbourne and wrecking a black R33 series 1 skyline

that my ex girlfriend wrote off. I have most parts available and they are all ready to post Australia wide.

All parts in excellent condition unless specified - Here is a short list:

- RB25DET engine with wiring loom and ECU 70,000k's

- diff

- right rear qtr panel

- all seats

- right door and door sill (door has 2 pin dents)

- carpet

- rear windscreen, drivers window and both rear quarter glass

- full set of brakes

- full set of standard springs

- dash Pad

- centre compartment

- glove box

- all pedals

- fuel pump

- HICAS system

- fuel tank

- rear bumper support

- electric aerial

- pair of brake lights

- most interior bits

- Boot + standard spoiler

- both electric window motors

Please genuine enquiries only thanx

You can easily contact me via email or phone thanks, Ben

[email protected]

OR 0401 598 511

Link to comment
https://www.sau.com.au/forums/topic/31295-r33-parts-available-update/
Share on other sites

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

ABuSD - I have the centre console bin and most interior parts still. The console bin I will sell for $50+

Craved - PM sent

Instrument Cluster SOLD

Drivers electric window motor SOLD

Keep it up everyone - All parts are ready to send immediately

You just call, we agree on a price, and I send

ok this mite so stupid, but how much are you willing to sell your passenger side carpets? and are you willin to send it to Sydney?

lol this sound stupid but i have been lookin for the passenger side carpet, as for some stupd reason, the standard ones has been taken out by the last owner, so ive wantin to get one to replace my current one as its toooo small~!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good to hear. Hopefully you're happy enough not to notice when driving and just enjoy yourself.
    • I mean, most of us just love cars. Doesnt necessarily have to be a skyline.
    • Did you pick up a manual cluster to remove the position indicator?  (Pretty sure the 34 has the gear position in the cluster, but it's been a while)
    • Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • 440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
×
×
  • Create New...