Jump to content
SAU Community

Recommended Posts

I am currently looking to import from Japan, i just wanted to know what auction company's you know of?

I am aware of http://www.japaneseusedcars.com/

Are there any other auctions in Japan worth looking at?

Also is it posible to do compliance yourself?

Link to comment
https://www.sau.com.au/forums/topic/313085-used-car-auctions-in-japan/
Share on other sites

You would be better off contacting someone like Iron Chef or Beer Baron from this site. Let them know what you're looking for and they'll search the auctions for you. If you're planning on buying the car yourself from Japan without a broker site unseen, I'd advise against it. Seen some shocking (and uncompliancable) cars bought that way.

You can't compliance the car yourself.... unless you become a Registered Automotive Workshop, which can take a long time and cost a massive amount of money.

If you do a search on this forum you should be able to find a link to some of the auctions so you can see what cars are around.

priestley's advice is spot on.

do not just buy a car from an exporter without having someone physically inspect it for you. to organise that the best idea is to use a broker. a broker will work hard for little money to get you a good car. they will also help save you time and money with organising compliance, customs clearance, and any other stuff you need done.

as he said you cannot comply a car yourself. to become eligible to comply a car under the SEVS scheme you need to be a RAW. to be a RAW you must be an ISO 9001 certified automotive workshop and even then you must add each model of car you want to comply to your schedule of vehicles. we are talking 10s and 10s if not 100s of thousands of dollars of investment here.

again, best bet it to go with a broker as they will most likely have friendly deals with one or more compliance workshops and will get a price much better than you could just coming in there cold.

  • 4 weeks later...
priestley's advice is spot on.

do not just buy a car from an exporter without having someone physically inspect it for you. to organise that the best idea is to use a broker. a broker will work hard for little money to get you a good car. they will also help save you time and money with organising compliance, customs clearance, and any other stuff you need done.

as he said you cannot comply a car yourself. to become eligible to comply a car under the SEVS scheme you need to be a RAW. to be a RAW you must be an ISO 9001 certified automotive workshop and even then you must add each model of car you want to comply to your schedule of vehicles. we are talking 10s and 10s if not 100s of thousands of dollars of investment here.

again, best bet it to go with a broker as they will most likely have friendly deals with one or more compliance workshops and will get a price much better than you could just coming in there cold.

Sorry to dig up an old thread, but I'm new to the importing game and am looking at a V35 skyline import... Anyways, what are the import company's you would recommend in Australia??

Sorry to dig up an old thread, but I'm new to the importing game and am looking at a V35 skyline import... Anyways, what are the import company's you would recommend in Australia??

hi mate, all the cars I've ever imported I buy and import myself so I have never used any aus importers to recommend to you. having said that with V35s now being fairly well stocked in aus, and prices on them falling fairly sharply of late I would also suggest that you look at some in aus too. don't let me talk you out of importing but they are one model where you could definitely score a nice one for a nice price in aus and have the benefit of seeing it in the flesh and getting it quicker. I would suggest that you don't really need a import company/car yard to import the car for you. a switched on broker with good record and good contacts is all you need to get things done. Small brokers can be good as (theoretically) they should have more time to spend on your particular needs and will work hard for you right up till you are driving away in your freshly complied and registered car. word of mouth is very important to us. There are a number on this forum that would be worth checking out for sure. talk to a couple and see who you like. money wise there would only be about $500 between the cheapest and the most expensive so price is not such a concern.

  • 4 years later...

Well, AS Far As I concerned, IF you are from London,UK, then I tell you do not do such long process just consult with Japan car import service in London,UK. They will provide you best used japanese cars at cheap price.

Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...