Jump to content
SAU Community

Recommended Posts

Has anyone run 225/50/16's on standard R33 GTST rims. I think from memory they are only 6.5" wide, so in theory 225 maybe a bit wide. Just after some first hand reports for street, track, or drift cause the standard 205 are way too skinny. Just trying to keep stock look, I have a set of 18" Zivell speed rims that I run from time to time, but rather run standos. Thinking about Kumho KU36 as I reckon they are good bang for buck.

Link to comment
https://www.sau.com.au/forums/topic/316375-2255016-on-standard-r33-gtst-rims/
Share on other sites

Street slow=Fine

Skids=Fine

Any speed type driving=Fail

My car understeers like crazy if Im pushing with them on, and dont even think of boost, unless sideways smokey action and steering with your throttle or hand brake is what your after.

They are OK for day to day going to work and thats it.

My 2 cents

  • 2 weeks later...
Street slow=Fine

Skids=Fine

Any speed type driving=Fail

My car understeers like crazy if Im pushing with them on, and dont even think of boost, unless sideways smokey action and steering with your throttle or hand brake is what your after.

They are OK for day to day going to work and thats it.

My 2 cents

I agree with all of that besides understeer.. My current set are Re001 225's all round and it's quite taily. Maybe just the way I drive tho :cheers:

205's feel very direct but ultimate grip level isn't fantastic and they look ridiculous especially from behind. 225's look much better but there is a LOT of sidewall slop. I found running 40psi to be reasonable, anything less is horrible.

225's for day to day fine, put 40psi in them unless you drive like a grandma and if you actually want to have fun then strap your 18's on.

If I had to choose for day to day driving I would still run 225's because the 205's just look retarded on a sports car. And yes, standard fitment options are 205/55/R16 and 225/50/R16.

I'm running 225/50 on s15 rims- they look waaay better than 205s and I didnt notice any deficiency in handling.

That being said, even with the old cheap Kumho 205s, I had no problems with straight line traction unless I dropped the clutch on launch. They were even good for reasonable 1/4 mile times!

your contact patch for 205 vs 225 is actually the same area, so straight line traction should be the same. the difference is the 205's are long and thin and 225's are short and fat, relatively speaking. it's the wider cross-section that helps with cornering grip.

unfortunately 225s have too much sidewall flex so turn in feels very vague. also once you exceed the traction boundaries the tyre moves about and again feels very vague, there's not a "limit" as such that you can treat with finesse but an area where traction comes and goes. yuck.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...