Jump to content
SAU Community

Recommended Posts

  • Replies 91
  • Created
  • Last Reply

Top Posters In This Topic

+1 to GTRs understeer in wet. On my 33, I had shitty china tyres and it just ploughs straight ahead... Say doing 30 or so...

Just saying quality tyres are the go. Toyo proxe on mine = perfect traction all round. Full throttle 2nd gear (straight line) = no slide, minor minor shudder from gripping...

Also, I took my sisters s13 fairly quick through a corner, gripped like it was bone dry. (Michelin Pilot Sport)

Edited by Ten Four

I don’t mind the rain at all however i am a bit cautious and also leave a good gap from the car in front of me....loosing traction shouldn’t be a problem.. more the fact as already stated if you put your foot down, or hit boost in 1,2, 3 ish your most likely just going to get wheel spin.. well in my car anyways.

Defiantly do a wet day at AHG so you get use to controlling and don’t panic in case it does tend to kick out a bit.

From a driver training course I did: pump your tires up. The intuitive thing would be to let your tires down right? Not so, because when you let your tires down, the centre of the tire makes less contact with the road. Even though it looks like you've got a fatter profile and its harder to steer so it feels like you're glued to the road - the middle bit that you can't see flexes upwards. It's only harder to steer because you're fighting the tire deforming due to lack of pressure. This also makes it more likely that you'll have a blowout - the tire wall is contantly flexing as it goes round and round so it heats up and wears faster.

Tires are actually a form of pump, that's why you have ridges in them - to pump the water away from the contact surface and out the back. Good contact = good tires. Letting your tires down in sand works because you're on a loose surface that changes its profile when you roll over it - so you want your tire to deform with the surface. Roads are hard so you don't want deformation :yes:.

Related: Manufacturers recommended pressures on your placard are actually a trade-off between ride-comfort and safety. If the placard says 32, go 36 or even a bit more. Uneven wear (when the centre of the tread wears faster than the outside) only really happens when you pump up to ludicrous pressures. Also, if you're running low-profiles, ignore the placard completely and run a few PSI over the manufacturer's recommended pressure.

I shit you not, since I started taking this advice - you have to be REALLY trying to break traction, it won't "just happen" and my tires are lasting a LOT longer.

thx 4 the advice my tires call for between 38 and 44 mine were at 35 this week pumped them up 2 day because just realized (yes i know im terrible) there now at 40 and will be putting them to 45 tomorrow.

and to all those saying that ppl that loose it are shit. back off its not like we try losing it. its dangerous as u will just slide across the top and have no control i saw a friend go into a tree trying to drift in the wet so thats the last thing i try to do.

the areas i have problems is were there are cars that stop and weight eg lights, stop signs etc. so hmmm stuff it im going to take of super slow stuff every body behind me im going to be the old granny driver for once.

So many hero drivers in this thread lol. Yes, you are better than everyone :yes:

Haha, true true.

Also, to be fair, I noticed that my first skyline (with stockies and cheap "get-er-complied" rubber) was a bit tail happy going round corners in the wet. I swear this is without being a tool or deliberately trying to over-cook it. There was one particular corner (Beaufort and Grand Prom) that really used to scare the shit out of me because of the angle you're going uphill as you're coming out of a corner.

Until I got wider rims and better tires I just had to take it REAL easy in the wet. By that I mean "driving miss daisy" not "still going too fast, just a little bit less so". The camber was out also when I first got the car so this may also have had something to do with it.

"Losing it" implies to me that you have swapped ends, getting a bit tail happy isn't "losing it".

Tyres also do make a HUGE difference.. when I had 34GTT rims on my skyline, they came with Linglong tyres on the back..turning a corner at any speed, and any throttle, in the wet and she would step out (maybe the 2-way AND the shit tyres had something to do with it).

+1 on the skidpan, learn how your car reacts in different situations and build some confidence to deal with those reactions. No need for the ZOMG IT WENT SIDEWAYZ shit.

Edited by bubba

Skidpan in a FWD > RWD > AWD with equally good tyres on each.

After a long dry spell, when the rain comes down & the oil sits on top, a new dimension is created.

Besides tyres and brakes, other variables include worn suspension, taking the correct line, brake early before the apex and not late yaddayadda

why are silvias and skylines so slippery in the wet?

when im in a normal car with someone and they go round a corner fast sometimes i shit myself thinking the car is gonna loose traction but it doesnt

by 'normal car' I'm assuming you mean FWD shitboxes like the excels and rollas... My explanation would be that RWD silvias/skylines would have different steering dynamics to the FWD (you can't get oversteer with FWD). And on top of that you probably have firmer spring rates which tend to transform your cornering force into lateral movement, while the excels/rollas have soft soft suspension which means they get more body roll (safer).

How do i drive in the rain? Um normally i just drive like everyother day. Are u people doing 100k's into corners or somesh*t? Harden up and stop drivin like spastics. Otherwise people in Canada etc put chains on their tyres, give that a shot.

How do i drive in the rain? Um normally i just drive like everyother day. Are u people doing 100k's into corners or somesh*t? Harden up and stop drivin like spastics. Otherwise people in Canada etc put chains on their tyres, give that a shot.

so u can honestly say that u have never stopped at lights were there is oil and lost traction. or driven a auto that has hard shifted from 1st to 2nd around a corner.

i know i dont drive like a spastic having never smashed in the rain and only smashed once on dry but i was not at fault. i drive with my lights on and leave extra space i just guess i take of a little 2 fast 4 my car. but thats the thing i can take of 2x faster in other cars so why do skylines seem to not like the wet (going by what other ppl are posting its not just me)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...