Jump to content
SAU Community

Recommended Posts

  • Replies 199
  • Created
  • Last Reply

Top Posters In This Topic

I just got mine fitted today. I got 19x9.5 +22 at the front and 19x10.5 +12 at the rear. They pop out a fair bit at the rear, I figure once I put some coil-overs on and drop it a little they should camber in and sit a little more flush. Either that or I put some spacers on the front.

Pretty happy so far, I do wish you could fit centre caps to them though.

post-77856-1291273819_thumb.jpg

post-77856-1291273900_thumb.jpg

hey ken i need a package for my r33 GTR, 19x10 or 19x10.5 with tyres.

can you give me a qoute ? thanks

Can do 19x10.5+22 with the following KU31

255/30/19 $5200

265/30/19 $5100

275/30/19 $5200

or

KU36 285/30/19 $4900 will need to check with kumho if they any stock left

I just got mine fitted today. I got 19x9.5 +22 at the front and 19x10.5 +12 at the rear. They pop out a fair bit at the rear, I figure once I put some coil-overs on and drop it a little they should camber in and sit a little more flush. Either that or I put some spacers on the front.

Pretty happy so far, I do wish you could fit centre caps to them though.

Looks good, but needs to be lowered.

Hey guys,

More stock is arriving at the end off the week!! So buy yourself a Christmas present!!

18x10+20

18x10.5+15

18x11+18

18x9.5+22

17x9.5+12

17x9+22

  • 3 weeks later...

What is the price difference between 18 x 10.5 and 19 x 10.5?

and do you know if you need gaurd rolling or anything for R33 GTR to fit 10.5's all round?

cheers

Daz.

Only $300, i don't think guard rolling is required for a R33 but the R32 it's a must. We also have 18x10+20 in stock if you want..

  • 1 month later...
  • 4 weeks later...

How much for a set of 18 by 9.5 +22 offset without tyres including shipping to Hamilton, New Zealand?

Freight would be a killer, if you can get a quote on your side it could be cheaper. i'll find out and advise on our side

hi mate looking for 18x10 et 35 and 18x9 et 35 as i need to put adapters to fit my car

They come in those sizes you want, the closest is 18x10+20 and 18x9.5+35 or 18x9.5+22. Not sure by what you mean adaptors? Do you mean spacers?

hi mate sorry should have explained, im looking to put them on my audi and need to fit an adaptor plate to do that. it usually knocks 15 off the et. looking to get rim size/offset close to 18x8.5/9.5x et13 and 18x10 et19 so im looking at offsets around et 28 and 35 before fitting the adaptor. sorry if i rambled on

hi mate sorry should have explained, im looking to put them on my audi and need to fit an adaptor plate to do that. it usually knocks 15 off the et. looking to get rim size/offset close to 18x8.5/9.5x et13 and 18x10 et19 so im looking at offsets around et 28 and 35 before fitting the adaptor. sorry if i rambled on

Ok the closest is in 5x114.3 is as following unless you want the normal TE37 which has a lager selection of offsets and iszes

18.9.5+35 or +22

18x10+20

Regular TE37- they don't come in 18x10 only 10.5+15 or +22

18x8.5+22 or +30

18x9.5+22 or +35

  • 2 weeks later...



  • Similar Content

  • Latest Posts

    • Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
    • Did some FASTing ...got the impression that the actual part# was a moot point ; seems all of these hardlines for coolant are discontinued/NLA... like, I take it you're after the hardline that bolts onto to the manifold...that's NLA according to amayama & nengun .... ...just to clear up some confusion, they typically mounted the AAC valve to the intake manifold somewhere near a coolant passage, so the body of the valve heats up & holds it open when engine's up to temp - no coolant flows through the valve, it's a mechanical, thermal connection.
    • And now the bloody flapper is jammed slightly open. Lazy as all f**k in 3rd-5th (very hard to convince it to make much boost before you run out of revs), but will make 12 psi in 1st, which shouldb't be possible with a 5 psi spring and controller set to <10 psi. Methinks I'm lucky it jammed where it did, rather than fully closed. It's actually a well weird situation. Careful examination of what's happening in the back of that housing when the gearbox comes out and all the other stuff (injectors, AFM retune) is supposed to be done, next week.
×
×
  • Create New...