Jump to content
SAU Community

Recommended Posts

I had awesome racing pedals in my last car, they were made specifically for the car and actually made a difference: They felt much better and I always noticed them (they looked great) on entering the car too which was nice.

I am after some racing pedals for my R32 GT-R. Any ideas? I have done asearch but couldn't find anything. And when I check out sites online they seem to sell a lot of different kinds of pedals but none of them sem to be specifically for the Skyline. Will all of these (Sparco, momo etc...) fit easily?

Link to comment
https://www.sau.com.au/forums/topic/31750-the-best-racing-pedals/
Share on other sites

Well, I find the rubber ones TOO grippy at times (ie: you can't really re-position your foot on a pedal unless you raise it off the pedal 1st). I had aluminium ones with raised steel studs (I think they were illegal actually as there was no rubber on them at all) and they were great.

i also have razo metal ones, and think they r great (alittle close together gas and brake alittle close but u get use 2 it)

hehehe no such thing as too close, there's plenty of room down there for big feet....you just need to get used to it

Contary the best racing pedals are no pedals at all.

Anything that comes between your foot and the actual factory pedal further reduces feel.

Its the reason why racing shoes are made with thin soles so as to enhance feel.

So after market pedal caps (i call them those becos thats what they are...they do not actually replace the factory pedals) are actually a step back.

If pedal placement is a problem (i.e u find it hard to heel toe because the pedals are too far apart) then u can try bending the pedal stem to get the pedals to sit at the correct height and position you desire

usuckpoo: fair call. But the surface of the pedal does make a difference in feel. Steel/aluminium feels different through shoes than rubber does. And perhaps one of the major difference is visual appeal. Which IS important to some of us. As I mentioned above, when I used to hop in the Alfa, with my black Novitec pedals from Germany... I'd look at them upon entry.. they made me smile.

Ive got a metal studded brake pedal and some dodgy type r accelerator pedal. Its actually ok as it sits close to the brake, making it easy to do that cool heel and toe thingo, allbeit poorly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...