Jump to content
SAU Community

Upgrading R32 Sound System

Vdragon

By Vdragon,
in Car Audio & Electrical

 Share

Recommended Posts

Vdragon Contributor

Vdragon

Posted
Posted

Hey guys just working on upgrading my stock R32 sound system. Just cant decided wat 2 put in. I dont really want a sub but i want a speakers that give u a good sound a bass so yeah just wondering wat u guys wud recommend i shud do.

Link to comment
https://www.sau.com.au/forums/topic/318917-upgrading-r32-sound-system/
Share on other sites
BeEnAr Experienced

BeEnAr

Posted
Posted

I run Pioneer TSD1702C 6.5inch Splits for the front (Great Speakers and very clear) you will need to make an MDF spacer to get them in under the factory grille and clear the window, Pioneer TS-A1682S 6inch 4-way speakers in the rear parcel shelf (they're ok I only got them to complete the sound stage), in the boot I do run a sub though, but it fits good and is in factory made box, it's a Pioneer TS-W307D2 - Champion Series 12inch. All this runs off a Pioneer GM6300F 600w 4 channel amp for the speakers and a Pioneer GMD7400M 800w Class D Mono Amplifier for the sub. All up a pretty well sorted system and does me fine with the added ability to remove the sub if I need too. Problem is fittin gthe amps to the back of the seat in the 32 as the boot isn't that roomy lol

GUN_METAL_GTR32 Grand Master

GUN_METAL_GTR32

Posted
Posted
a mate of mine put in these JL midi bass speakers 6 inch i think in the bak of his 34 tho... for a car with no sub their fairly decent... around 600 bux tho...

yeah they arent bad

i have the next model up in the doors of my 34 they were around 729. then jl 6x9's in the parcel shelf. 2 jl amps and an jl 12 inch and it f**king rocks.

it doesnt come cheap though.

Carbon 34 Grand Master

Carbon 34

Posted
Posted

think we have hashed this subject a few hundred times now...lol use the search function

those Black Death "Vibe" brand speakers are new to OZ, been around England for a while now. there not any better then average gear. just something new style wise.

Vdragon Contributor

Vdragon

Posted
  • Author
Posted
I run Pioneer TSD1702C 6.5inch Splits for the front (Great Speakers and very clear) you will need to make an MDF spacer to get them in under the factory grille and clear the window, Pioneer TS-A1682S 6inch 4-way speakers in the rear parcel shelf (they're ok I only got them to complete the sound stage), in the boot I do run a sub though, but it fits good and is in factory made box, it's a Pioneer TS-W307D2 - Champion Series 12inch. All this runs off a Pioneer GM6300F 600w 4 channel amp for the speakers and a Pioneer GMD7400M 800w Class D Mono Amplifier for the sub. All up a pretty well sorted system and does me fine with the added ability to remove the sub if I need too. Problem is fittin gthe amps to the back of the seat in the 32 as the boot isn't that roomy lol

ey mate how much did that cost u all up? coz it sounds awsome might look into a bit more

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Tekitsune
      Upgrade an rb25neo

      By Tekitsune 路 Posted

      Hello, just just bought an 1999 enr34 with a stock rb25neo and I'm looking to upgrade the engine to 500whp I know some basic things but wondering if there are things I'll need to do to upgrade the stock block and all the bits and pieces to achieve this.
    • DatsunBanana
      Rear subframe stay bracket bolt removal issues

      By DatsunBanana 路 Posted

      Thanks everyone for the replies and suggestions. Got the seats out (hoping I could find some existing grommets but no such luck). By tapping and measuring etc. I could figure out where I could drill through if needed. But first I borrowed an inspection camera and managed to go through factory holes in the chassis rail and could see that the captive nut was holding steady which is why it could retighten. So it was indeed a stripped section of thread, so I applied downforce by levering the bolt head with a screwdriver and went slowly back and forth until it came out. Camera helped a lot cos I could monitor that the captive nut was holding tight. Now I just have one very seized main subframe nut to tackle 馃槄
    • Dose Pipe Sutututu
      Question about BoV on RB25DET NEO

      By Dose Pipe Sutututu 路 Posted

      BOVs do have a purpose, if you ever log pressure before and after the throttle body, you will see a spike pre throttle on lift off from a WOT condition. Enough to bend throttle blades / damage e-throttle motors or simple assist in blowing off cooler pipes. FWIW, the above on really applies to those running at least 2 bar of boost. OP shouldn't have an issue, on the other hand, here are some videos of my shit box over a decade ago with some succulent dose with the airbox on and off. That shit box is unrecognisable these days 馃珷    
    • Yeetus
      Question about BoV on RB25DET NEO

      By Yeetus 路 Posted

      I've tried all different combinations of BOVs/ no BOV and stock bypass valves over the years, on gear changes the stock bypass valve seems to get the car back on boost quicker because in part the turbos wheel speed isn't being slowed down by reversion, although they have issues holding boost much over the stock setting. Most aftermarket BOVs you can adjust the spring, tighter will make it open later and close sooner, but in my experience it'll cause a bit of flutter at low load/rpm anyway. I've also got some input into this whole no bov causing turbo wear, never had an issue on any on my turbos HOWEVER, I got my R33 GTST with 200k kms on it, with from what I can see still has the original turbo, no lateral shaft play but has about 4-5mm of play in and out which to me seems like a worn thrust bearing from years (100-150k kms?) of turbo flutter running no bov, so maybe there is some truth to it in the long run. But that'll never stop me loving the Stutututu while I have the car.   OP just wants to know if he can run a atmo vented BOV with no major issues and the answer is YES, plenty of people do it, there's no harm in installing it and seeing how it runs before spending $$$ on an aftermarket ecu, last time I bought a Nistune it was $2400 for install and a tune , unsure of todays prices but you get me. Crazy money to spend just to fix the minor inconvenience of stalling that can be overcome by letting the revs come down to near idle before putting the clutch in or a little bit of throttle to avoid it. You're better off leaving the ecu and tune for after a bigger turbo/injectors have been installed to take full advantage of the tune and get your moneys worth.   Let OP have his Whoosh sound without trying to break his bank haha
    • MBS206
      Question about BoV on RB25DET NEO

      By MBS206 路 Posted

      I see you missed the rest of the conversation where they have benefits, but nothing to do with avoiding breaking turbos, which is what the aftermarket BOV made all the fan boys, tuners, and modders believe was the only purpose for them...
脳
脳
  • Create New...