Jump to content
SAU Community

Recommended Posts

Hey guys,

I was listening to the car idle yesterday with my head in the engine bay and noticed a slight ringing, trying to think og how to describe it, maybe like rotating a bell so that the tongue thing grazes around the outside rather than shaking it to cause impact between the tongue and bell. that was poor haha

yeah, so anyways what exactly does pinging sound like? and has anyone noticed this before? it'd be fantastic if i just had to tighten a bolt, but it's never that easy.

car is an r34 gtt with cat back exhaust, stock elsewhere but running an indicated 12-13psi for reasons i have not yet found

thanks for any help/advice!

Link to comment
https://www.sau.com.au/forums/topic/319040-car-ringing-quietly/
Share on other sites

if ur running that much boost that could be the sound of your turbo on the way out, does it get louder as revs rise or when u hit boost? pinging is a yucky noise it sounds like pieces of metal tapping loudly together.

ahh, that's good news about pinging and bad about the turbo. figuring out why the boost is so high is now top of the list lol.

it was only ringing on idle, and it couldn't be heard in the cabin, so not sure if the noise is there on boost. i used the throttle control in the engine bay to increase revs and it disappeared, then reappeared very faintly at (guessing) 2500rpm, like it was something vibrating.

if it was the turbo, would it only make noise on boost?

what does high boost stress from the turbo, the impeller or compressor? and im guessing a new stock gtt turbo is pretty costly?

it would make more noise on boost normally, like a loud shreaking noise, or grinding if its blown a turbo.

a second hand one in good nick is usually $300, so not that much, can also get them reconditioned.

im no mechanic, and fairly new with these cars, best bet is take it to a mechanic or better a performance shop they could tell you in minutes.

if you are getting pinging at idle then you have issues. but i'd say that it isn't pinging and it is possibly a worn bearing in the clutch. or a pulley bearing. but it is very hard to say without hearing it.

also turbo noise would get worse when you hit boost if it was dying.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...