Jump to content
SAU Community

Recommended Posts

Hi Guys

last week i noticed this for the first time, i drove from Newcastle to Port, went through some hills and my car started to splutter and loose power now this was new to me as it wasn't a missfire as such but more of a sruggle to make power then die.

i have worked at Port all week and the car has been fine, not a drama. i gave it a boot afew times and nothing. Now last night i drove to Coffs and it was fine but today i was giving it a little and about 15mins latter it spluttered and died in the middle of a round a bout mind you lol.

It seems to happen when the car is hot, could this be spark plugs/coil packs? at first i thought fuel pump but it's been fine all week.

it's really wierd.

Mods: front mount

3.5inch exaust

Standard turbo

Boost controller running 10psi

coil packs are stock but siliconed

i pulled the plugs out thisarvo and they have the usual blackness and coil packs look okay.

Any ideas?

Cheers

Cam

Link to comment
https://www.sau.com.au/forums/topic/319804-problem-with-r33-gts-t/
Share on other sites

ok, if it is the CAS will this slowly get worse? can this be easy tested to see if it is? and how much roughly to fix?

at this stage with work i don't have the time to fix but need my car, if it's easy to do yourself i will do it.

i drove it today for about 5mins just to see if it would go, it seems to be when it gets hot it does it

cheers for the help guy

Cam

well the known baddie you have is the taped/botched coilpacks

you already know these were causing an issue last time as you have repaired them

so the most likely culprit is the coilpacks - i can't understand how the CAS is at fault, unless it has come loose

how often does a CAS fail? i cant recall a single CAS Failure? it seems in the last two weeks everyone posts "CAS" is at fault. check the basics. check your coilpacks, check base timing at idle (that would confirm if CAS is toast or not)

If it died in the middle of the round a bout then i'd say CAS.

Won't be coil packs.

CAS's play up in some fken weird ways. Car can be fine for a week and randomly die, and then it might die twice in the next hour and then be fine again for another week.

My CAS when it was failing did exactly that - made it a bastard to diagnose

Ahuh...cheers..i always figured it was a sensor of some sort causing it, it only really happens when cars been undriven for a while, if i give it a bit of a flogging it always corrected itself...

So what would be wrong with it, or does it just need replacing?

  • 2 weeks later...
  • 2 months later...

Hi guys, thought I would let you know the diagnosis of my problem. Turns out it was a faulty airflow meter, yep the symptoms matched what you guys were saying about the Cas had it looked at didn't find nothing, when it did it again we put the computer on it and yay. So take note the airflow meter can cause similar issues, and after a new set of coil packs, plugs, I even got a cas. thank god we got there

cam

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The trigger kit I have is similar to the one in the link below. While going through Facebook, I saw someone else mention a similar issue, and I’m starting to think this could be related to the crank gear itself. I understand these parts are CNC machined, but maybe some earlier versions or individual pieces might have slight inconsistencies—it just doesn’t look right in my case. https://www.facebook.com/share/16an8evZd9/?mibextid=wwXIfr I originally installed the crank gear using the thin OEM washer, but as shown in the attached photo, the timing belt walks very close to the edge. When I tried using a Nitto washer—which is thicker—it actually made the issue worse. The belt walks about 1mm off the front edge, which raises more concern about alignment.   I’ve gone through the full process of elimination:   The tensioner pulley and bolt are brand new and installed correctly. The bolt isn’t bent and is oriented properly. The back of the tensioner and the idler pulley are clean and seated correctly. The idler sits slightly more forward, which I understand is due to its design. I’ve experimented with both tight and loose belt tension, but it makes no difference. As soon as the engine runs, the belt immediately walks forward again—even if I reset it beforehand.     At this point, I’m considering replacing the crank gear with your Race Version 1 (12-tooth), but before purchasing, I wanted to ask:   Are you aware of any alignment issues when using this gear? Would this gear help keep the belt aligned correctly, or could the walking still occur? Does it work with a standard missing-tooth crank and rear washer? Is there any specific crank setup or install procedure required?     For reference, I’m not using a front washer, as the PRP crank gear seems to replace the need for one.   Looking forward to your advice.
    • Yep, looks that way. Never driven an E30 or R31 so I can only imagine  
    • Yuh, My new R34 box is sitting on the workshop floor (in its large shipping box, which is a nice thing on its own), along with a front plate to convert to push clutch. There was no way I was interested in rebuilding my existing one. Was only partly interested in the risk of buying a used one. But, if you want a 2nd hander, I can point you to one in/near Melbourne at least. @Komdotkom has one that should be in good enough condition to be usable. I don't think it's in a for sale thread, you'd have to message him. @redzedhas one that definitely needs a rebuild.
    • I used to love going to Amaroo to watch the HQ series go for broke (eventually stopped due to lack of spare parts) and also the Porsche series.  It was so cool to back your car up to nearly the edge of the viewing barrier and party with your friends, having a bbq and alcoholic/non drinks. It was such a family/mates atmosphere
×
×
  • Create New...