Jump to content
SAU Community

Recommended Posts

but i must add one thing, it is very hard to et an r32 in perth atm, i duno mostly r33 all over the place, im looking for a r32 gtst wid gtr kit or m spec, but noone seems to have one, i was looking at spending nythin up to 17k on it

but nyways, thats my twenty two cents

I'm looking at importing a 1989 R32 GTS-t through Prestige Motorsport within the next few months (to have it imported after May). Obviously, I need to get a car built in May, but I'll persevere.

 

Anyway, I want to find out how much most people spent on compliancing their R32's, so I know how much money I'll have to spent on the car itself. It seems most examples go for around $8000, inc. the broker's fee, and exc. compliancing.

 

I have about $10000 all up.

The pits are cracking down at the moment but usual stuff to get road worthy.

Oil leaks,bushes, shocks, brakes and so on but if you buy a clean car you will have less problems. look around localy as well before you comit.

Concave mirrors pass now, fuel filler cap Pull out your self and get somebody to braze it in, High mount stop light might not be required, child restraints $20, exhausts are being picked on now.

Not to much over here.

Contact Phil at Phills mechanical and see what he can do for you he even takes the car over the pit for you, less stress. Phone. 9493 3069

Side intrusion bars are not regulated like it is in other states. Call Phil and he will give the run down.

Look at www.j-spec.com.au as he lists the cars at the auction and can purchase Yahoo ones.

Also cars do come off Yahoo so look at this link and the one below is the start of Skylines in Japan translated.

http://babelfish.altavista.com/babelfish/u...ion%2Fd44004135

http://babelfish.altavista.com/babelfish/u...egory-leaf.html

aye elithar if ure looking for advice call 'kengtr' he use to import cars, and now has own shop, but he gave me some valuable info if i wanted to import, like never have the car held in japan unless in locked up garage with security as many ppl have had things stolens uch as wheels, stereo, gauges etc, and also if u have to wait it stays outside for the japan winter....which isnt to pleasent on ny car...let alone an 89 model...

but yer give him a call

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...