Jump to content
SAU Community

Recommended Posts

hey guys

i got defected the other week in my r32gtst

he only got me for

fmic

exhaust

bov

wasnt aware at the time he ticked full inspection so pretty much everything has to come off needs a blue slip... so coming off is.

fmic

exhaust

bov.

rims

gauges on pillar

pod (boxed)

catch can

i hide my boost controller and turbo timer behind dvd player haha he didnt notice on his first inspection

the guy didnt say anything about my coilovers though???

dont think he could tell about the r33 turbo either

and its got a nistune board in it, injectors fuel pump rah rah but he wouldnt notice would he?

it should be all passed by this w,e

and most of the parts will be back on it by the end of the w,e as some stock parts are borrowed..

i want to get some stuff engineered

mainly the

exhaust,fmic and pod in box

how hard is it to get them engineered and roughly costs?

i doubt my exhaust will be under the 90db.. its a x-force 3"

(opinions of how to make it quiter without restricing the flow)(maybe change change cannon to different muffler?)

its a greddy fmic so i doubt the piping kit is legal had to make an extra hole.

so is it still possible to get engineered?

apexi pod is full boxed

any help will be appreciated thanks

Link to comment
https://www.sau.com.au/forums/topic/320390-defect-and-engineering-advice/
Share on other sites

if you want the FMIC done you will need to pass the IM240 emissions test, not that easy to get through but you can get a retune and should pass ok.

Bascially each engeineer is different and might be ok with some things and not others best off to speak to one directly, if you in Newcastle then there is one in Cardiff and he is on the approved list from the RTA look him up or do a google search if not there is a list of approved ones on the RTA site that is the best way to do it rather than ask other people.

Good luck, the cops in Newy are pretty hard on cars trust me i know :P

you will have a better chance of passing the IM240 test if you have a cat from a fairly new car (couple years old) as they have much stricter emissions standards to meet than a car from the early 90's, the only problem is finding one.

tooo bad... I left Australia a year ago =)

Where did you go? You took your car didn't you.... I saw a vid of you doing skids in Georgia and was like "WTF.... THAT is dedication....."

If you're on the European continent with that thing, I dearly hope you plan on paying the Nürburgring a visit.

http://www.skylinesaustralia.com/forums/Gu...mp;hl=guilt-toy

Where did you go? You took your car didn't you.... I saw a vid of you doing skids in Georgia and was like "WTF.... THAT is dedication....."

If you're on the European continent with that thing, I dearly hope you plan on paying the Nürburgring a visit.

I've always wondered, if your car is SEVed and gets compliance with all the gear already on it, you have the full report, and then is continually registered..........where does that leave you?????

BTW if you are pulled over again and you have re installed all the 'bad bits' afterwards and they find out, you'll end up somebodies bitch in gaol, they'll throw the book at you - or thats my understanding of it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...