Jump to content
SAU Community

Microtech Dyno Tuner

campbellbullock
 Share

Recommended Posts

  • 4 months later...
pabs89 Newbie

pabs89

Posted
Posted

well i got an S13, with a CA18, 32GTR injectors, Bosch 040 fuel pump, Sard Fuel reg.... oil catch can (wich does f**k all) T28R turbo... making 196rwkw, and it hits boost and pings (pretty much cuts out) and comes back to normal, gay as! apparently the microtech uses too much fuel (runs too rich) im looking for someone good in townsville (north qld)any suggestions???? PLEEEASE!! i need some help

mad082 Grand Master

mad082

Posted
Posted

pinging isn't caused by too much fuel. it's caused by either not enough fuel or too much timing or not high enough octane rating or too hot spark plugs. any of these cause combustion temps to rise and contribute to pinging.

as for looking for a tuner, try asking in the QLD section. pretty sure there is even a thread for townsville people, so try looking in there

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dylannn
      For Sale Haltech Elite Plug n Play

      By Dylannn · Posted

      Hey   ive gone for a terminated harness on my build so selling brand new unused and unopened piggy back harness  https://www.haltech.com/product/ht-141357-elite-2000-2500-nissan-skyline-r32-33-r34-gt-r/ Located Bathurst NSW   price $600 + postage     
    • drifter17a
      Rb25 trigger kit and timing misalignment

      By drifter17a · Posted

      The trigger kit I have is similar to the one in the link below. While going through Facebook, I saw someone else mention a similar issue, and I’m starting to think this could be related to the crank gear itself. I understand these parts are CNC machined, but maybe some earlier versions or individual pieces might have slight inconsistencies—it just doesn’t look right in my case. https://www.facebook.com/share/16an8evZd9/?mibextid=wwXIfr I originally installed the crank gear using the thin OEM washer, but as shown in the attached photo, the timing belt walks very close to the edge. When I tried using a Nitto washer—which is thicker—it actually made the issue worse. The belt walks about 1mm off the front edge, which raises more concern about alignment.   I’ve gone through the full process of elimination:   The tensioner pulley and bolt are brand new and installed correctly. The bolt isn’t bent and is oriented properly. The back of the tensioner and the idler pulley are clean and seated correctly. The idler sits slightly more forward, which I understand is due to its design. I’ve experimented with both tight and loose belt tension, but it makes no difference. As soon as the engine runs, the belt immediately walks forward again—even if I reset it beforehand.     At this point, I’m considering replacing the crank gear with your Race Version 1 (12-tooth), but before purchasing, I wanted to ask:   Are you aware of any alignment issues when using this gear? Would this gear help keep the belt aligned correctly, or could the walking still occur? Does it work with a standard missing-tooth crank and rear washer? Is there any specific crank setup or install procedure required?     For reference, I’m not using a front washer, as the PRP crank gear seems to replace the need for one.   Looking forward to your advice.
    • PranK
      ATCC Amaroo Park 1987

      By PranK · Posted

      Yep, looks that way. Never driven an E30 or R31 so I can only imagine  
    • Dose Pipe Sutututu
      Rb25 trigger kit and timing misalignment

      By Dose Pipe Sutututu · Posted

      Post up some photos
    • GTSBoy
      WTB RB25 Gearbox NSW / central west

      By GTSBoy · Posted

      Yuh, My new R34 box is sitting on the workshop floor (in its large shipping box, which is a nice thing on its own), along with a front plate to convert to push clutch. There was no way I was interested in rebuilding my existing one. Was only partly interested in the risk of buying a used one. But, if you want a 2nd hander, I can point you to one in/near Melbourne at least. @Komdotkom has one that should be in good enough condition to be usable. I don't think it's in a for sale thread, you'd have to message him. @redzedhas one that definitely needs a rebuild.
×
×
  • Create New...