Jump to content
SAU Community

Recommended Posts

ok, i have an R32 GTS-T and a full 3 inch exhaust with a cannon. i have seen my mates GT-R make meter long flames and just wondering why mine doesn't?

i know it's to do with unburnt fuel and a hot exhaust igniting it, and mine makes some fery loud pops! but i've just never been able to get a flame! i have had mates repeatedly rev it to see... some pops are really loud cracks and some are deep thuds. anyone know anything about this?

Link to comment
https://www.sau.com.au/forums/topic/322087-why-no-flames/
Share on other sites

get a b r limiter , they are like the mad core . the flames make your way car faster . but it drifts weird if your exhaust isnt in the middle . pull the exhaust off at the dump pipe and itll make it do wheelies

+1 but my car did back flips instead of wheelies... i think i pulled to much of the exhaust off

Link to comment
https://www.sau.com.au/forums/topic/322087-why-no-flames/#findComment-5253297
Share on other sites

all GTR's need is a gutted cat or de-cat and you will get flames.

mine lets flames out a fair bit with de-cat but as others have said over time the rear bar gets black shit over it which does come off but is annoying. Will probs be getting 3M clear film/sticker for rear bar protection or just chuck a high flow in soon.

Link to comment
https://www.sau.com.au/forums/topic/322087-why-no-flames/#findComment-5253305
Share on other sites

Step 1: remove cat

Step 2: turn off the decel fuel cut on computer

Step 3: pay ridiculous amounts of money in fuel to burn rear bar

you forgot to add in step 4, which is "say goodbye to the exhaust wheel of the stock turbo as it gets drastically weakened by the excess heat and decides to part company with the turbo and go on a holiday out the exhaust"

also i think this pic belongs in this thread

18173_105868542766058_100000287384092_149269_6916618_n.jpg

Link to comment
https://www.sau.com.au/forums/topic/322087-why-no-flames/#findComment-5253314
Share on other sites

So can high flow cats still permit flames (200 cel or 100 cel)? Or does it fully have to be no cat (too loud)? Does it work with non turbo engines? Technically it should because it is unburnt fuel and exhaust heat, unless the turbo contributes to a lot more heat...

Link to comment
https://www.sau.com.au/forums/topic/322087-why-no-flames/#findComment-5254595
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So..... it's going to be a heater hose or other coolant hose at the rear of the head/plenum. Or it's going to be one of the welch plugs on the back of the motor, which is a motor out thing to fix.
    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
×
×
  • Create New...