Jump to content
SAU Community

Recommended Posts

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

hey luke!

do you by chance have the squishy rubber hose that goes from the front turbo inlet elbow to the air flow meter/airbox? - think i can see it in the box in that pic you posted up

also wondering if you have the following hose?

http://www.skylinesaustralia.com/forums/post-a286350-

"14463MG" in the image.

oh, and a stock rear turbo oil drain? ;) AHEM.

If it's in the box Nigel ur welcome to it. Best to come down and have a look. I'm going all alloy piping so getting rid of all the rubber stuff I've got.

Luke

Whole list of parts for sale from my 1999 R34 N/A GT-four sedan.

Front seats $200 pair with rails

Rear seats $150

All seat belts $200

Parcel shelf with 4 tweeter holes cut out $50

Roof lining in black velour $150

All pillars in black velour $60

Fuel tank $250

Front bar $200

Front guards $ 200

Bonnet (couple of stone chips/pin dents $250

Bonnet latch $50

Bonnet hinges $50

Cusco Master cylinder stopper $80

Glove box $50

Kick panels $80

Door Trims $100

Cusco Full bolt in cage $1200

Brake master cylinder $120

R34 GT-four gear box, Small crunch 3-4. Chuck some redline in and she'll be right, Complete manual conversion $1200 Will include clutch master, pedal etc

Clutch pedal $120

Clutch master $80

Brake pedal $50

Accelerator pedal $50

R34 N/A brakes complete set, discs, calipers, lines $300

R34 N/A air box $50

All Air con stuff $200

Brake lines $50

Heater box (non leaking) $150

ABS module $150

Climate control display $150

Bnr34 brembo's low k's, slotted rotors, A1RM pads, braided lines, complete set $2800

R34 Rear hubs, handbrake set-up, handbrake lever, lca, $300

If your after a stock part that isnt there let me know.

Will be adding more as i think of it.

Cheers Luke

Hi there i'm after the hazard light switch for my r34 gtt sedan. Have u got it if yes for how much including postage to 3073.

Cheers :laugh:

hey mate your front bar standard?

sure is mate. It's got the factory fog light holes but the brackets were all rusted so took them out. Also got the little antenna in the front passenger area, but doesn't work anymore.

Also keeping the hazard thing as I may need it.

Edited by Luke_ENR34
  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...