Jump to content
SAU Community

Recommended Posts

Hey guys,

I left my car with at the mechanics all week as it needed the front left lower control arm replaced. Unsure why, but they decided to leave it till today before working on my car and because they ordered the wrong part they didn't end up finishing the job till about 5.30pm.

So now I have a new front lower control arm, bushes but no wheel alignment, and I'm meant to be leaving for DECA tomorrow morning at 4am. The mechanic took it for a test drive and said it wasn't too badly out of alignment, the car will drift very slightly to the right, but nothing severe. He claims I could probably get away with a morning of DECA and then get an alignment over lunch. Once I got home though I took another look (20-25min drive) and noticed the inside of both the front wheels had more of a fresh rubber look (rather than being dusty and dirty like the rest of the tyre, it was clean) and it was significantly warmer than the outside of the tyre.

Am I safe to drive 250km tomorrow to Shepparton, and then compete, or should I just call the whole thing off? I'm guessing I shouldn't go, but I was really looking forward to this and I don't particularly want to lose my money.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/323569-wheel-out-of-alignment/
Share on other sites

If have wheel at -5 and +1 toe on the front and still drove to Sydney for track time. Will scrub the tyres. If the car doesn't pull to hard to either side it can't be to bad. Depends on how much you care about you tyres.

Its easy to adjust. Toe out the left wheel or toe in the right. You can do it in 5 minutes and then go for a drive. Has to be better than what you have currently.

Just drive it man. How good are your tyres? Look up all the tyre places in shep and have numbers ready. call them all at 8am tomorrow and get it in after scrutineering. you'll still do most of the day. You'll lose your entry fee anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...