Jump to content
SAU Community

Recommended Posts

Hey guys,

I left my car with at the mechanics all week as it needed the front left lower control arm replaced. Unsure why, but they decided to leave it till today before working on my car and because they ordered the wrong part they didn't end up finishing the job till about 5.30pm.

So now I have a new front lower control arm, bushes but no wheel alignment, and I'm meant to be leaving for DECA tomorrow morning at 4am. The mechanic took it for a test drive and said it wasn't too badly out of alignment, the car will drift very slightly to the right, but nothing severe. He claims I could probably get away with a morning of DECA and then get an alignment over lunch. Once I got home though I took another look (20-25min drive) and noticed the inside of both the front wheels had more of a fresh rubber look (rather than being dusty and dirty like the rest of the tyre, it was clean) and it was significantly warmer than the outside of the tyre.

Am I safe to drive 250km tomorrow to Shepparton, and then compete, or should I just call the whole thing off? I'm guessing I shouldn't go, but I was really looking forward to this and I don't particularly want to lose my money.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/323569-wheel-out-of-alignment/
Share on other sites

If have wheel at -5 and +1 toe on the front and still drove to Sydney for track time. Will scrub the tyres. If the car doesn't pull to hard to either side it can't be to bad. Depends on how much you care about you tyres.

Its easy to adjust. Toe out the left wheel or toe in the right. You can do it in 5 minutes and then go for a drive. Has to be better than what you have currently.

Just drive it man. How good are your tyres? Look up all the tyre places in shep and have numbers ready. call them all at 8am tomorrow and get it in after scrutineering. you'll still do most of the day. You'll lose your entry fee anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...