Jump to content
SAU Community

E10/100 On A Pulp98 Tune - Any Issues?

gwilkinson34
 Share

Recommended Posts

gwilkinson34 Collaborator

gwilkinson34

Posted
  • Author
Posted
You need a retune to make use.

Just changing fuel will not realise the full benefits.

There is extra timing and fuel mappings that need changes to see the gains that are to be had.

That's what I thought, but is there any danger?

ie due to the ethanol content not flowing enough fuel on the PULP98 tune? Or is 10% ethanol not enough to drastically change the flow requirements?

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Should be ok, I tried it a while back for its higher octane but I found little difference in knock protection between that and BP98. If you want benefits re-tune for E85, more pumps should become available very soon.

gwilkinson34 Collaborator

gwilkinson34

Posted
  • Author
Posted
Should be ok, I tried it a while back for its higher octane but I found little difference in knock protection between that and BP98. If you want benefits re-tune for E85, more pumps should become available very soon.

No worries. Yeah i plan on getting a netbook to plug into the Haltech and tuning a map for E85 so i can switch between the two as need arises... Just dropped $10k+ on the car though so perhaps i'll leave it a while.. ;)

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
That's what I thought, but is there any danger?

ie due to the ethanol content not flowing enough fuel on the PULP98 tune? Or is 10% ethanol not enough to drastically change the flow requirements?

Well not overtly major other than the "why?" ;)

Just use as is until you are tuned for it.

gwilkinson34 Collaborator

gwilkinson34

Posted
  • Author
Posted
Well not overtly major other than the "why?" :down:

Just use as is until you are tuned for it.

I just happened to be at the airport and needed some petty. United had E10/100 and as i'm not sure what their 98 is like i thought i'd chuck half a tank in.

Just wanted to make sure it wasn't going to break anything :blink:

gwilkinson34 Collaborator

gwilkinson34

Posted
  • Author
Posted
i use E10/100 ron and i certainly rate it. its about 1.20 a L most days and ive tuned my car to suit the fuel. awesome torque gains from few degrees extra timing.

Would tuning for it be that easy - just bung in another couple degrees and run it up on the dyno to make sure it's still not near detonation?

Harey Veteran

Harey

Posted
Posted (edited)

after all the dollars you spent on a custom tune I would just run 98. I would only run the E10/100 ron fuel if you took it back for a quick retune.

I tried the E10/100 ron fuel a while ago and I got 5L/100km worse fuel economy for no gain in power (because I didnt get a tune). So I quickly changed back to 98.

Just wait for E85 and get a custom tune done then.

Edited by Harey
gwilkinson34 Collaborator

gwilkinson34

Posted
  • Author
Posted
after all the dollars you spent on a custom tune I would just run 98. I would only run the E10/100 ron fuel if you took it back for a quick retune.

I tried the E10/100 ron fuel a while ago and I got 5L/100km worse fuel economy for no gain in power (because I didnt get a tune). So I quickly changed back to 98.

Just wait for E85 and get a custom tune done then.

Aight :blink:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • drifter17a
      Rb25 trigger kit and timing misalignment

      By drifter17a · Posted

      The trigger kit I have is similar to the one in the link below. While going through Facebook, I saw someone else mention a similar issue, and I’m starting to think this could be related to the crank gear itself. I understand these parts are CNC machined, but maybe some earlier versions or individual pieces might have slight inconsistencies—it just doesn’t look right in my case. https://www.facebook.com/share/16an8evZd9/?mibextid=wwXIfr I originally installed the crank gear using the thin OEM washer, but as shown in the attached photo, the timing belt walks very close to the edge. When I tried using a Nitto washer—which is thicker—it actually made the issue worse. The belt walks about 1mm off the front edge, which raises more concern about alignment.   I’ve gone through the full process of elimination:   The tensioner pulley and bolt are brand new and installed correctly. The bolt isn’t bent and is oriented properly. The back of the tensioner and the idler pulley are clean and seated correctly. The idler sits slightly more forward, which I understand is due to its design. I’ve experimented with both tight and loose belt tension, but it makes no difference. As soon as the engine runs, the belt immediately walks forward again—even if I reset it beforehand.     At this point, I’m considering replacing the crank gear with your Race Version 1 (12-tooth), but before purchasing, I wanted to ask:   Are you aware of any alignment issues when using this gear? Would this gear help keep the belt aligned correctly, or could the walking still occur? Does it work with a standard missing-tooth crank and rear washer? Is there any specific crank setup or install procedure required?     For reference, I’m not using a front washer, as the PRP crank gear seems to replace the need for one.   Looking forward to your advice.
    • PranK
      ATCC Amaroo Park 1987

      By PranK · Posted

      Yep, looks that way. Never driven an E30 or R31 so I can only imagine  
    • Dose Pipe Sutututu
      Rb25 trigger kit and timing misalignment

      By Dose Pipe Sutututu · Posted

      Post up some photos
    • GTSBoy
      WTB RB25 Gearbox NSW / central west

      By GTSBoy · Posted

      Yuh, My new R34 box is sitting on the workshop floor (in its large shipping box, which is a nice thing on its own), along with a front plate to convert to push clutch. There was no way I was interested in rebuilding my existing one. Was only partly interested in the risk of buying a used one. But, if you want a 2nd hander, I can point you to one in/near Melbourne at least. @Komdotkom has one that should be in good enough condition to be usable. I don't think it's in a for sale thread, you'd have to message him. @redzedhas one that definitely needs a rebuild.
    • Watermouse
      ATCC Amaroo Park 1987

      By Watermouse · Posted

      I used to love going to Amaroo to watch the HQ series go for broke (eventually stopped due to lack of spare parts) and also the Porsche series.  It was so cool to back your car up to nearly the edge of the viewing barrier and party with your friends, having a bbq and alcoholic/non drinks. It was such a family/mates atmosphere
×
×
  • Create New...