Jump to content
SAU Community

Recommended Posts

Couldnt find the noob section here

(dont think it exists)

ive just got a r33 gtst (first turbo)

cars pretty stock cept the exhaust

and ive been told not to start the car immediately and drive

and i should let it warm up

in many instances im short for time and cant start it up and wait 5 mins

is this going to be a big problem

btw i do not boost while the engine is cold

dont give much throttle and change gears around 2.5krpm

Link to comment
https://www.sau.com.au/forums/topic/323929-noob-question/
Share on other sites

1. congrats

2. letting a car idle for ages is bad for it, it's a lot longer runtime for the engine when it's not in an optimum state (cold)

3. start car, let it idle for ~20 seconds to let the oil circulate and then drive off gently. I stay under 3.5k if possible and no boost until it's warm.

whoever told you to start your car and idle it for 5 minutes deserves a stiff backhander. you're not doing the car ANY favours.

Link to comment
https://www.sau.com.au/forums/topic/323929-noob-question/#findComment-5279457
Share on other sites

+1 to above post some of the most important factors are having a car reach optimal running temp as quickly as possible.... too cold.. fuel is like sludge too hot and u overheat.... these days its fair cold so ye start the car 20seconds is perfect enough to then drive try get ur car to warm temp asap!

Link to comment
https://www.sau.com.au/forums/topic/323929-noob-question/#findComment-5279466
Share on other sites

+1 for what has been said above. people seem to think that skylines (and most imports for that matter) are some magical monster race engines that should be treated differently to any other engine, when in fact they aren't. you will find that in japan the original owners would've hopped straight in and driven off on much colder mornings than we get here.

just keep it off boost until the temp needle has reached half way and has been there for a minute or 2.

Link to comment
https://www.sau.com.au/forums/topic/323929-noob-question/#findComment-5280350
Share on other sites

Not even necessary to wait 20 seconds. The oil will be circulating within a few revolutions of the engine actually starting (don't forget you've been pumping oil while cranking to start).

Simply start engine, into gear and away you go. Every second that you delay is wasting fuel, and the excess fuel delivered while the engine is cold is risking dilution / thinning of the oil.

Link to comment
https://www.sau.com.au/forums/topic/323929-noob-question/#findComment-5281616
Share on other sites

an extra 20 sec isn't going to waste that much fuel, and it makes sure that oil has gotten through out the whole engine.

not sure about you but my engine starts pretty quickly, there is no way the oil has gone through the whole engine in the 2 or 3 seconds it takes to start. remember also that the cold oil moves a lot slower so it wouldn't run through engine and more importantly the turbo and be lubricating as it should that quickly.

if you have ever had an oil temp gauge in your car you would realise that your oil doesn't heat up much until after your water has come to operating temp.

i typically start car then go check my letterbox then hope inside and drive off.

Link to comment
https://www.sau.com.au/forums/topic/323929-noob-question/#findComment-5283477
Share on other sites

the hop in and drive off thing also comes down to where you keep your car, etc. if you park it in a garage and you have to reverse down the driveway, wait for cars, and then go then you really could just hop in, start the car, once it is running just start going, because the first 20 seconds or so of the car running you pretty much aren't doing anything more than just idling the car. if you park out on the street and can literally hop in and drive off straight away then it is a different matter.

at my place i will hop in, start the car, let it run for a second and then select reverse. all i have to do is let the clutch out enough to just grab a bit and the car will start rolling down the yard, then i just need to let it out a little bit to clear the gutter. then i can just turn the steering wheel and start rolling fowards down the street. i'll just put it straight into second gear, let the clutch out at about 10kmh and just stay idling along in second until the end of the street (about 4 houses away).

Link to comment
https://www.sau.com.au/forums/topic/323929-noob-question/#findComment-5283549
Share on other sites

I usually let the car sit for a minute or 2 just to let the fluids cycle through and then drive off and keep off boost for about 5 - 10 mins before boosting.

Once the car has reached normal operating temperatures, you are all good to go.

Before switching the car off, just drive off boost for a few mins and/or let the car sit and idle for a few mins and you'd be fine.

If you have been hammering it, give it more 'cool down' time.

Link to comment
https://www.sau.com.au/forums/topic/323929-noob-question/#findComment-5283690
Share on other sites

yes sort of. the best thing to do with any car though is to simply drive sensible for the last km or so before you get to where you are going. the car will cool down better when it is actually moving than it will just sitting there running. this way also your brakes, etc will also cool down a bit and not have super hot pads sitting against a rotor in the one spot as this can cause warping, etc.

if you drive the last minute or so of driving normally then you can just turn the car off and walk away when you get there. this includes turbo cars.

Link to comment
https://www.sau.com.au/forums/topic/323929-noob-question/#findComment-5285269
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • And if you want more power, more reliably, and cheaper, go get the Aussie RB... The 4L Barra and put that in instead.
    • No cats will keep discolouring the rear bar. Sends white paint a weird yellow stain. Cut and polish normally gets it out, but you'll be doing that every fortnight I found.
    • Both heads will be equally reliable or unreliable depending on what you do to them.  Stock the RB26 head will flow more. You have access to the stock intake ITB manifold on the RB26 cheaply which flows really well(1000hp+).   Arguably more aftermarket support for RB26, though in Aus we love our RB30 SOHC heads too.    The only downsides to the RB26 head is if you have a VL commodore and want to keep the SOHC look.  Where you may have an issue is drilling out the rb30 block for the bigger head studs but if you are building a big power motor you'd probably put bigger studs on the SOHC head too.  This is just about finding a good machine shop, sometimes easier said than done.  RB30 head worked can make big power just like a Rb26 head, so really it actually more comes down to what your preference is for your car.  People now even making billet versions of both.
    • 2630s work perfectly well. There is something to be said for just using the 30 head, as it saves all the pain of the conversion, still makes tons of power, still sounds cool, etc etc. 2630 will obviously make more power again, but the differences are not stupidly big. It really depends on whether you're racing for sheep stations or not. If it's dead serious, then it's a 26 head. If it's just for fun, it could go either way. But the 26 head and the effort to get it set up, etc etc, is part of the fun.
    • I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani Refurbed astra pump thats the cover for it in the boot I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
×
×
  • Create New...