Jump to content
SAU Community

Recommended Posts

Got the car when it had 68,000km Fresh from japan, now its 116,000kms Ive also done the 100,000km Service, On top of all these mods bellow,

Type B Tomei adjustable Cams ( Cant remember the measurments, but they are lumpy on idling)

Tomei Dump pipes

Sard 720cc injectors

Sard intank fuel pump

PFC

Z32 AFMS

Air pods

Garret -5 turbos

Fuel Regulator

Greddy Boost Controller 2 profec B

Oil - Air seperator catch Can

Xtreme Single plate Heavy Duty Clutch

Os Giken 5 gear set

Alluminium intercooler/turbo piping

Oil cooler

Spitfire coils

3.5 inch exhaust

600hp rated Cat convertor

ALL INTERNALS ARE STOCK

Now long story short I got a tune done but little did the the tuner know there was a rip in one of the hoses this was before i got the piping done, So he set it to 15psi and the car was doing 316-320awkw, He pretty much tuned the car around the leak and everything looked fine, after i got the the pipiing done the car went quicker id say the boost went up automatically, must of been all that extra air going to through. Since then i have taken it to the tuner, his played alittle with the mixtures and so on but didnt touch the boost assuming its where he left it, he was pretty happy with everything, VERY little Knock. I checked the boost recently cause i found out how to and it peaked at around 21psi And now id say its 350awkw-360awkw.

Is this bad for the car? because its got stock internals how long roughly would will she last with all this beating last time i checked the compression was around 165psi on all cylinders. that was at the 100,000km mark.

Edited by GTRAAH
Link to comment
https://www.sau.com.au/forums/topic/324144-is-this-bad-for-my-car/
Share on other sites

with a good tune there is no reason a street driven RB26 cant last a while @ 350rwkw

BUT

imho you should re dyno it and have the boost set where YOU are happy with and have the power level that YOU are happy and confident with.

edit: when this happened to me, we fixed the leak and my tuner didn't even finish 1 pass as he noticed the boost hit 26psi and was still climbing.

run was pulled and boost was re-set

make of that what you will :wacko:

with a good tune there is no reason a street driven RB26 cant last a while @ 350rwkw

BUT

imho you should re dyno it and have the boost set where YOU are happy with and have the power level that YOU are happy and confident with.

edit: when this happened to me, we fixed the leak and my tuner didn't even finish 1 pass as he noticed the boost hit 26psi and was still climbing.

run was pulled and boost was re-set

make of that what you will :wacko:

Im definately happy with 21psi but i feel that it might climb alittle higher but nothing past 22psi id say. But if i set it to 21psi i want to keep it around 3-4 yrs before i do my Internals Etc So i want it too last for that long

Edited by GTRAAH

well im saying 3-4 yrs time i want to rebuild the insides i only drive this car maybe 2-3 times a week, Sorry i forgot to tell you all its not an everyday car as in im not boosting all the time PLUS its my weekend car, Does that change things? i want it to last 3-4 yrs healthy before an internal rebuild, And i have just talked to the tuner and he stated that it wasnt pinging or knocking on that PSI setting

Edited by GTRAAH

its hard to say what is safe amount of power as ppl with stock engines have had to rebuid as well.. generally accepted with more boost on stock internal GTR, its good to keep it around 300kw mark to "prolong" its life.. its no guarantee but perhaps better odds than pumping out another 30-50kw and placing more stress.. also if your tune is good and u look after it well, no reason it wont last the distance, but sometimes luck of the draw

Thanks BWRGTR, Is there anyway to keep an Eye out on the wear and tear?

Used oil analysis is the only way I know of. Basically, every oil change you send off a sample of the oil to a lab and they send you a report. Its been discussed here before so search if you're interested.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...