Jump to content
SAU Community

Recommended Posts

Ok,

When driving after 30mins or so. Either highway or backstreets (probly more highway, strangely)

The car will heat up, according to the temp gauge.

I have an alloy radiator, with a thermo on the back. No stock clutch fan, just thermo and it runs 100% of the time.

The other crappy fan on the front of the a/c cooler is also fitted.

When i drive on the highway 80km/h or less it sits about half way..

100km/h+ it will rise.

100 it slowly rises, 110km/h it rises much faster ....

Any ideas ?..

I was thinking just the temp. switch but really not sure. I come to this thought because while on the highway and it is 3/4+ on the gauge, i put car in neutral and switch off. The turn it back on straight away (after engine stops) and the gauge is half way again.

??

When at 3/4 temp, and i stop the car the overflow bottle does NOT seem to be boiling or getting water pumped into it.

Had the same problem with clutch fan, which is why i went to the thermo. But still has a bloody overheat problem

I have flushed the radiator twice. fitted a thermo and it runs all the time when ignition is on. just at the higher revs it seems to heat up quicker (3200rpm or higher)

Any thoughts ?.. (was thinking of taken it to red devil radiators or somewhere.. as in take entire car there, but really tight on funds atm)

Link to comment
https://www.sau.com.au/forums/topic/324667-helpopinions-on-overheating-problem/
Share on other sites

i'd start by either buying an aftermarket water temp gauge, or getting a consult cable. with the consult cable you can see what the temp is that the ecu seeing. it uses a different sensor to the dash. either of those options will allow you to see whether the problem is actually a temp issue or a sensor/gauge issue.

if it does turn out to be a heating issue then it could be caused by the thermostat ot possibly the water pump.

also i hope you aren't turning the car off while cruising along at 100kmh.

mad's advice is good. But if it were me i'd just pull the thermostat out, and go for a drive to see if that's it. If that fixes it get a definitely fit a new one as it helps your motor get up to temperature quicker, and that's important in the long term.

Thanks for fast reply.. Pulled out thermo stat.

Seems good, although i didnt take car for a drive with no thermostat installed.

I tested it with boiled water from kettle and it opend up ect..

Re-installed it and went for a run...

Im pretty sure its a blocked up radiator as its a 2nd hand one... was fitted just over a week ago (and hte problems were there from then in a way)

Whats it cost for a professinal flush/clean ?

Im located southside of Brisbane so any advice on where to take it to ? (i know its cheaper if i pull it out of the car)

Firstly, having the thermo running 100% of the time is basically defeating the purpose for having a thermo. It only needs to run when the temp gets too high - and by too high, I mean 10 or more over thermostated temp.

The general problem I have found is getting air to flow through the radiator. It is too easy for air to simply travel down the front of the radiator and out underneath the car.

Is the fan turning in the correct direction, ie pulling air through the radiator? And it probably wouldn't hurt to get the radiator cleaned and serviced, particularly as it's second hand.

Ok, played more today

Found that the alloy radio had a fair bit of crap still in it

I have removed that and put a stock one back in. With thermo attached.

Now it doesnt get above half.... Yet to test on track.

Im thinking of going back to clutchfan and shroud (i need a new shroud).

I have 2 thermo fans setup.. i done the same to my ole RX7 and that thing never ever got hot. (one on front pushing air, one on the rear sucking air)

I know it takes that little bit longer to warm up.

Anyhow, after using acid to flushout/soak the radiator(s) i found that even more brown crap came out. After a reverse-flush with garden hose that is.

Afterwards i used acid, and caustic soda (lean mixture) and then Battery acid. (advised these are the best to use by a helpful fella at Radiator shop @ Archerfield).

The acid removed quite alot of more crap. that the standard flushing wouldnt use.

thermo's are fine if set up correctly if you dont want to go back to the clutch fan on the engine. for controlling the fans use a SPAL fan-pwm fan controller to control the fans, great piece of kit costs between $250-275 depending on where you get it from, you can get them from air con wholesalers JAYAIR or any good radiator shops. Not to hard to fit good instructions. It uses pulse width modulation to control one of your fans which slowly increases fan speed from 50% to 100% from a predetermined set point that you program and if running 2 fans will start the 2nd when the high point is reached.If you have a big FMIC this can also affect the amount of airflow to the rad look at fitting a top panel where your bonnet catch is from the front bar to rad support and the same on the bottom to force air through rad air will take path of least resistance -this is a common mistake on gtr's where the front splitter is removed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...