Jump to content
SAU Community

Recommended Posts

Hi Guys,

I am trying to clean up my wheels. The middle part of the wheel cleans up nice with some wheel cleaner. However the dish remains stained. I have tried different wheel cleaners but it seems to be within the metal now. I also tried quickly some metal polish but no luck either.

Any ideas?

Here is a pic, needs to be closer but you get the idea.

post-29432-1276648538_thumb.jpg

Tried "Upper Engine Cleaner" from Subaru?

It could remove all the sh/t that was on my OEM wheels from Japan.

It works if Zymol wheel cleaner doesn't.

When it's all off, you may need to respray the wheels with 'clear'.

Ah ok yup thats the next step if I cant do it pretty easily myself.

After some google searching I found two products, ALUPLUS and ALUBRITE. It is an acid that is supposed to clean aluminium and then polish it really well.

Think I will try that and then resort to a rim repair shop if it doesnt work.

That ALUBRITE is a pretty harsh acid, Ive used it to clean the outside of the head, the cross over pipe and stuff like that.

ALUBRITE will burn your hands if you dont wear gloves its that strong, it will eat the duco as well and anything else that gets in its way... Ive used it in conjunction with a toothbrush to clean all sorts of things... it'll clean brake dust build up off rims, but it will also scar the paint and leave shiny alloy dull, I havnt tried it on powdercoat...

But it should work on the aluminium dish of my rims as long as I dont get it anywhere else?

I will just try a very small part of the dish with a toothbrush to start off with.

Edited by Harey

As mentioned alloy brightener can make shiny alloy dull but if you then polish it you should be ok...

Be careful with the stuff. Wear a mask or don't breathe, & wear gloves. I use it at work to clean transmission cases & it's strong stuff!

You'll know when you breathe it in...

Edited by wlspn

hey... okay here's what you do.

first of all.. this method sounds strange and it will be MOST noticable with bad rims (i mean RIM rims... not "wheels")

go to bunnings

get a very fine steel wool.

no. not that dishwashing crap that you use to get black stuff off pots. this is steel. wool. SIFA make it.

2175040__32055_thumb.jpg

looks like that.

rip a chunk off. big chunk. the bigger the chunk, the more surface area you have to scrub with. the more surface area. the less pressure. less pressure, less chance of scratching. get it?

use either water - or olive oil as a lubricant... i suggest olive oil as it won't ake the steel wool RUST. use a lot of it.

gently rub the steel wool on the wheel. if the stains won't come out, apply a little bit more pressure etc

the basic premise of this is... steel wool is soft as butter. but it is still a METAL. your aluminium / steel rims are a harder metal, and will not "give in" to the steel wool easilly

the steel wool sacrifices itself to clean the metal.

give it a go if you so wish - i imagine that there is a certain element of risk doing this method... but i've done it plenty of times on my wheels which - at one stage were VERY badly corroded.

steel wool is about 8/9 bucks

everyone else take note.

oh and wash the olive oil off the rim using a soap / detergent / shampoo (dah)

  • 1 month later...
i think you need to determine if the dish area is clearcoated from factory - if it is, you will most likely need to remove that before being able to polish it.

Your right on the money here, the dish does have a clear coat.

I started with the steel wool and it wasnt doing much, so I went a bit harder and I could see it take the clear coat off and go down to metal. I have only done this in one small area.

What issues does removing the clear coat raise? Should I remove it or just leave it there and give up.

These guys seem use aircraft stripper to remove the clear coat:

http://forums.corral.net/forums/showthread.php?t=763405

They just say it takes a bit more effort to keep em clean. Its only the dish of my wheels so dont have little nooks and crannys that would be tricky to keep clean.

Would love the rims to have a super shiny dish :happy:

I am leaning towards removing the clear coat.

Edited by Harey

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...