Jump to content
SAU Community

Japan Roadtrip - Photos of Tokyo Autosalon 2004 and more


Recommended Posts

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

I have had a request to delete all references to "Rice" that have f*cked up an otherwise brilliant thread.

First and last warning guys...

Remember: the more you argue about Rice in the Japan Forum, the smaller your pen!s gets...

As far as I'm concerned a "Ricey Car" is a 1.5 Carby 4 door Lancer with an Evo 4 kit and Altezzas on 13" Black steelies.

That Yashio 15 was one of the nicest turned out cars at the Salon - my favourite of the show - if I remember correctly they quoted a "street trim" 400hp from it - more than enough to take care of 99% of Rexes.

In the words of the immortal Eazy E - "I can afford to laff cos I'm backing it up" - If a car has enough grunt then it can have a bit of rice.

My 14 will be bagged and riced to the hilt - but it will have 300rwhp and be sub 5 to 100 capable - is that OK?

Top pics Blitz - We're processing the 7 or 800 remaining pics - we've only got 165 of Race Queens tho...

Jash

  • 1 month later...

There was 1 DR30 on display DaiOni - The Tomica DR30 Touring Car was on display on the Bridgestone/Nismo stand in the carpark on the far side of Makuhari. There's a pic of it in one of our galleries.

Jash

We actually stumbled across that bit of the show by accident while we were looking around the side streets for cool cars. We actually found last years G Corp Sileighty parked along the canal.

Jash

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...