Jump to content
SAU Community

Recommended Posts

So I've been soaking all my dirty parts in degreaser and scrubbing with a friggin toothbrush saying "well it's only one time, just do it" but it seems like every now and then I have to do it again. I use the 'export quality' degreaser as well as the 'kenco heavy duty' one @ 2:1 ratio water:degreaser (it's their most concentrated recommendation but I have used it straight) which is ok for regular stuff but doesn't do much for the fun stuff until I scrub... hard.

I CBF spending so much time hitting it with a brush so to futureproof myself, do you have a better method?

So I've been soaking all my dirty parts in degreaser and scrubbing with a friggin toothbrush saying "well it's only one time, just do it" but it seems like every now and then I have to do it again. I use the 'export quality' degreaser as well as the 'kenco heavy duty' one @ 2:1 ratio water:degreaser (it's their most concentrated recommendation but I have used it straight) which is ok for regular stuff but doesn't do much for the fun stuff until I scrub... hard.

I CBF spending so much time hitting it with a brush so to futureproof myself, do you have a better method?

there is an industrial degreaser from bunnings that i found was the best on the retail market - $60 for 15L and is green/yellow in colour

simple green works well also in high concentrations - and available from bunnings

both these need soaking though - so overnight in a tub and then pressure hose them off.

another handy household cleaner for baked on oil is oven cleaner left on for about 5-10 mins the hosed off.. can help to scrub this a little also but works wonders (dont leave on too long or it discolours alloy)

ive always used motorspray degreaser and cant say ive even thought about complaining about its strength.

its the stuff u get at paint shops in 4L. i just apply it with a paintbrush, sometimes it needs some work with the brush then just wash off with a hose.

can i just ask what you are actually asking here? are you asking for a better degreaser to make it so you don't have to scrub it as much to get it clean, or are you saying that you clean the parts and then a little while down the track they get dirty again?

if it's for the scrubbing bit, stuff that is really caked on will usually need a bit of scrubbing. you won't really find too many products that actually eat through seriously caked on crud. for this stuff you are best off giving it a light soak (few mins), then giving it a bit of a scrub then soaking it again and then a final scrub if needed. this way when you scrub it then soak it for the second time you are allowing the degreaser to penetrate more.

A better degreaser or method to clean so I don't have to scrub it as much.

I've had a few gearbox conversions go through on my car and every time I'd be there scrubbing away at the new gearbox saying "it's only once"... turned out to be 3 'onces'. I recently got some GTR32 brakes so was scrubbing them and I know these brakes won't last me... I can see myself scrubbing once again and I'm already dreading it.

Thanks for the ideas, I'll give those suggestions a try next :D

Now what to do with 4L of crappy new kenco degreaser.. hmm...

if it is alloy that you are cleaning, try getting some alloy cleaner. it's a chemical that you mix with water and it cleans alloy really well. don't think it does much on steel though. i use it on my boat and it's good stuff. doesn't get much of the grease off, but it gets the stains off. it kind of bleaches the alloy, LOL.

if you want to get some stronger degreaser, look in the phone book under "chemicals - industrial". there should be someone who has some super strength degreaser. but you'll probably have to buy it in either 5 or 10L, and it will probably cost a fair bit, but it will be strong stuff. the sort of stuff that when it says to dillute it, you dillute it or it will eat your skin.

if it is alloy that you are cleaning, try getting some alloy cleaner. it's a chemical that you mix with water and it cleans alloy really well. don't think it does much on steel though. i use it on my boat and it's good stuff. doesn't get much of the grease off, but it gets the stains off. it kind of bleaches the alloy, LOL.

if you want to get some stronger degreaser, look in the phone book under "chemicals - industrial". there should be someone who has some super strength degreaser. but you'll probably have to buy it in either 5 or 10L, and it will probably cost a fair bit, but it will be strong stuff. the sort of stuff that when it says to dillute it, you dillute it or it will eat your skin.

sounds like alibrite or allumabrite - which is normally a sulfuric acid mix for cleaning alloy.

i've been through a few of those "industrial degreasers" which were up to $400 for 20L and the bunnings green stuff was alot better.

a can of oven cleaner will do a whole gearbox - just cannot get it on any of the plastics or rubber boots.

pretty sure the stuff i use is blitz aluminium cleaner. probably the same thing though. i just get it from supercheap for about $15 for 1L. the liquid is bright pink.

upon a bit of looking around, yeah it's the blitz stuff.

taken from the website

BLITZ ALUMINIUM CLEANER

Chemtech Blitz is a unique formulation specifically designed for the effective cleaning of any aluminium or stainless applications such as intercoolers, turbo chargers, valve covers, radiators, bull bars, dinghies, side steps in part preparation of a high gloss finish. Blitz is safer to use than products containing hydrofluoric acid.

so it can also be used on stainless

Or you could buy a pressure cleaner [karcher, spitwater etc], use the degreaser and then wash off with the karcher. A good pressure cleaner can take your skin off at 100mm, so use gloves when holding parts and getting into it.

I have a 5L bottle of Kenco cleaner, sprayed some of it on the oil stain in the garage and it took most of it off. It cleaned all of the oil and grease of my engine. Also tried the truck wash at a spray paint workshop, very strong stuff.

For grease/oil - kerosene, tho some use diesel. The water based degreasers i've used have been hopeless, but they'd probably be ok for cleaning off the kerosene.

+1 for kerosene - works great only problem is it tends to leave a slight "film" of kerosene. Pressure washer off the stuff afterward and you will be laughing.

Another thing I recommend for parts that do not get too hot is to put wax on them afterward on visual/cosmetic surfaces - don't put wax on "working"/mechanical surfaces surfaces - any gel wax would suffice - this helps dirt and other crap from sticking easily.

you use wd40 as a cleaner? umm, why not use degreaser or something like that which is actually designed to remove grease?

WD40 is a grease remover. if you have a greased joint you should NOT use WD40 on it, unless it is seized... in which case you can help anti-seize it with WD40 but you must clean the WD40 off it afterwards and re-grease the joint.

i like using R60 solvent. dries clean eats the crud away quickly tho i havent tried it with brake parts. You also have to watch as if you get dermatitis on your hands it'll make ya have a reaction

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...