Jump to content
SAU Community

Recommended Posts

I envy the quietness of your car! After a while off loudness you will be wishing you left it as is and IMO the induction noise is way cooler then a loud exhaust note.

If your exhaust flows well and your making the power your happy with and its nice and quiet. Thats something I would wish for before world peace!

I'm a fan for quietness but my exhaust was too restrictive so took out the middle muffler (don't have or need a cat in NZ) and now it goes well and is still not too loud.

Get a hacksaw (or better still a pipe cutter) and cut out your middle muffler and fit a bit of pipe temporarily. If you like the result get it welded in if not you can weld the middle muffler back in.

A loud exhaust is a good way to annoy the neighbours and attract the attention of the police.

Everyone has a different definition of "loud", that much is certain... and often the law has another view all together...

So do what you want TUF250, but just remember its highly likely any mods will almost ensure EPA's will come your way.

Are 3inch pipes any good for the car? Like say from the catback straight pipe no muffler or anything? could it mess my tune up if i change it? as i have a greddy one?

u mean flutes? be noisy as fark dont think its gona do anything to your performance positive or negative.

I dont want it to be silly, I had a V8 previously with just resinators and it sounded great but it really was stupid and eventually got annoying.

Unless my rb is over 4-5k rpm there really is no noise at all. My dads stock xr6 turbo makes more noise! I was just after a burble. Not into cannons, big resinators only or anything like that. Just wanted a bit of burble not bark.

Thats why I thought id leave the rear muffler (the biggest) and remove the centre but I dont want to make it too loud and get myself into trouble.

its a tricky one...

It literally makes almost no noise. It is completely drained drowned out by the induction noise.
If the induction noise is too loud, why not do something about quietening it, like enclosing it in an air box.
3 inch dump pipe high flow cat and lukey turbo muffler 3in 3 out. no police attention but loud enough and seems to flow enough

I have a 4 inch from my T88 turbo back. I had the exhaust custom made with a 4 inch dump coming out pointing at the ground (rotaflo muffler)

It's loud as f**k, on a piston engine it would probably be a little quieter.

  • 2 weeks later...

i've just got a 3" system from turbo back. with a single remus muffler. the sound is sweet. quiet when you're not on the gas and the system is nice and straight so a good note

coming down through the gears. but it has exceptional flow at WOT.

Edited by wacky_will

I would say to be cautious with mucking around with the exhaust chasing a given sound. Odds are you will end up with 'not quite what youre after' and louder than u want.

Quiet is better id say, and im in WA where you can do whatever the f*k you want :down:

My old R33 was loud as. Good for 10% of the time, annoying for the rest.

The current R33 makes twice the power but is quiet as. I love it. Then again i have a pod so it is dead quiet when chilling and an angry tornado under gas. Best of both worlds.

Maybe look at that mod to make turbo induction noise. I think it is a way sweeter noise than exhaust (as good as an RB can sound at the tailpipe) noted by another post above.

I turn way more heads with all induction noise on this one than all exhaust noise on the last one....

And yeah, Vic sounds very cop-strict so a loud exhaust is going to give you nightmares me-thinks.

Goodluck mate

thanks guys, ended up pulling that middle muffler out, quite happy now, only a touch louder and has a slightly deeper note, still very quiet highly doubt it will attract any more attention.

note. I am selling that straight through 3inch stainless muffler if anyone is interested in a high flow 'quiet' muffler

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...