Jump to content
SAU Community

Rb20det Gear Box, Help Needed

r33_4dr

By r33_4dr,
in Drivetrain and transmission

 Share

Recommended Posts

r33_4dr Contributor

r33_4dr

Posted
Posted

does any one know the part number for the input shaft bearing for an rb20det gear box. also does any one have a factory type manual on the gearbox i cant find one all i can find is engine manuals. does any one know what the gearbox is actually called?

Link to comment
Share on other sites
Dan_J Veteran

Dan_J

Posted
Posted

u mean the copper spigot bearing that sits in the rear of the block ?

dont need a part number, just ask for a r32 spigot bearing. i think its ment to be the same for all manual nissan's

Link to comment
Share on other sites
The Dan Grand Master

The Dan

Posted
Posted

I think he might mean the actual input shaft bearing, not the pilot bush.

The part number you need for any bearings supplier is 6306 C3N or something with a 3 in the last digits. Don't get a regular 6306, the C3N depicts a extra tolerance gearbox bearing.

Link to comment
Share on other sites
Trozzle Grand Master

Trozzle

Posted
Posted

You'd think this would be the easiest part to find for any Nissan manual box....bloody horrible bearing, I'm yet to drive a skyline/VL commo where it hasn't eaten shit

Link to comment
Share on other sites
r33_4dr Contributor

r33_4dr

Posted
  • Author
Posted

yeah i mean the input shaft bearing, i know where it is and how to get to it ect but i dont know the part number or any thing for it. its off my a31 cefiro with rb20det. so is 6306 C3N the right number for the input shaft bearing for an rb20det gear box.

cheers

Link to comment
Share on other sites
Trozzle Grand Master

Trozzle

Posted
Posted

If the bearing is a problem, it's more than likely in pieces through the gearbox.

When the input bearing failed on our VL (RB30) gearbox, we found VERY LARGE pieces of the cage etc in the oil when we dropped it...good luck reading it lol

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Rezz
      Gran Turismo 7 Time trial

      By Rezz · Posted

      Does this count as a time trial as well? I got all gold in the master super licence (1 lap time trial) and received a McLaren MP4/4 for my trouble.  If anyone else has done this, did you ride the wall right around the first long right hander at Lake Louise snow track to get gold? I couldn't do it any other way... best I could do without riding the was was within 2 tenths of the gold time.
    • MBS206
      MLR's Bogan cruise ship

      By MBS206 · Posted

      I definitely get the low power, sporty car to drive to smash gears but not be doing eleventy million miles an hour! It makes all the normal drives fun!   Rev match tune sounds like the funs! I didn't know the NC had a DBW throttle!   As for me, still have the Skyline, it still has the Barra in it. It's been pushed to the side of the workshop at the moment. Pretty much waiting on me finishing the wiring, and dropping new fuel lines in. Got myself an ACDC Tig end of last year so been teaching myself TIG welding to build a few things for the Skyline. The missus wrote off her GTB liberty at the end of last year, and got it back on salvage rights stupid cheap. It's also still registered, so will mean easier for me to take to the track already done most of the panel damage, just playing "clear the workshop" to make space to pull the motor and box out, fix some oil leaks, replace the clutch, and replace a few minor broken things.  Also got a Lathe at the start of the year, which is adding to the annoyance of no space, which is another reason I'm trying to build things to get more space, to get the Lathe back in a final home for it. It's a BIG lathe, can turn a 355mm diameter, and 1metre between centres... Got it at a steal! So between it and the TIG and old MIG welder, I'll be fabbing some fun little shit up But we've had a lot of shit stuff happening at home, so it's slow going getting things done. But one step at a time!
    • PranK
      Gran Turismo 7 Time trial

      By PranK · Posted

      I love Catalunya.  Got a 1:54.632. The AMG is a hoot.
    • Kinkstaah
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Kinkstaah · Posted

      I hadn't got that far, my main worry was the connection to the actual calipers themselves. I'm just using new (ish) stock brake lines in the stock setup. I've just had a stud welded to the knuckle that is a little lower than the original stud (so my knuckles have two studs each side) to not have it be stretched so far in previous BBK setups, so the "block" (in the second picture) mounts a little lower for me and I hope I don't need to change anything. I may have even changed the connection to the calipers in the past and have since forgotten I did that. I may not have. Guess how I'm gonna find out. Source: hopium
    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      It's more so I'm using the 1x piece line from HEL that goes from the body to the caliper. There's no middle block/mount like the HFM ones or the GKtech ones. There are certain angles/suspension compression where the line actually slightly contacts the ARB. Below of how mine sit (not my photo): How I want it:  
×
×
  • Create New...