Jump to content
SAU Community

Recommended Posts

http://www.skylinesaustralia.com/forums/post-a307564-

^^

That looks MINT!

Love the bonnet, could you possible tell me where you got it from?

Edited by El_Mutto

Thanks dude. Yeah been keeping an eye out for a front lip. So hard to find a good looking lip, only one around is the EastBear. Really wouldn't mind something different though.

Yeah I liked the old rims also, but I was getting out dished by my Honda mate's so decided to go concave rims instead lol. Not too sure what rims I should go for next. Was thinking AME TM-02

I like the TE's, they look like they're 17's right?

A mate of mine just recently got AME TM-02's, only then did I realise that they look like the rims I just ordered, Enkei Rpf1's. A bit of research and I found out that the AME tm-02's are made by Enkei, pretty much the same wheels.

Yeah TE37's are 17x9+22 all round.

Had a set of AME Nobleys previous and realised that they were made by Enkei lol. AME TM-02 in aggressive offset looks so good with massive concave though :thumbsup:

Can I borrow your TE's :) look sweet in 17's with concave!!

lol EastBear looks great, but was hoping to find something different

18's looks good but I think it looks a tad too big for the GT-t. Plus I like the curved spokes :)

I would if you still had the XD9's :thumbsup: Your car looks awesome with the XD9's

Edited by john-e boi

nice ride john e boi i like the bride seats rear wing and wheels looks tuff :mrt:

i wana get a front lip for mine east bear looks like the one i have the side skirts and rear pods

need to finish her off

wot u think i should leave the front with melb roads being so f!@#$t up and that

maybe de-badge the rear and east bear aero bonnet

both east bear front bars and bonnets

:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...