Jump to content
SAU Community

Recommended Posts

i got a set of freshly recon'd 550cc purple tops off ebay and just wondering if any one knows much about them. i have heard if your fuel is rich in ethanol it can cause damage. i only every put 98 octane in my car so will this be a problem??? anyone with a set? im hoping that it is just an over exageration

Link to comment
https://www.sau.com.au/forums/topic/329578-nismo-550cc-purple-tops-question/
Share on other sites

uploading a pic now to silence all, these will be going on my rb25, he says their high impedance but he tells me had them/or was gonna put them on his gtr but didnt. would these fit no problems with a aftermarket fuel rail

post-74158-1279547152_thumb.jpg

Edited by chrislesnar

What motor is this going on? NEO or R33 RB25?

And no ethanol does not harm injectors. (forgot to answer this earlier) The mythology is, that ethanol corrodes old fuel lines. Realistically this is a non event for most skyline users anyway, really only a variable if you run an E85 setup, and even then there arent THAT many rubber hoses to replace in the car anyway.

What colour is std, I thought purple was std???

Mines a '98 R33 and I've got yellow tops= nismo 555's and they flow like that as well - they were on the car already from Japan, but I'm sure that purple tops were the std colour in '98 rb25's??

Purple is stocko for RB25, but it looks to be a different purple again lol.

If I were you, the risk is too big, why muck around with all that. Snap up a second hand set of nismo 555s or 740s for 700 bucks, plug and play.

They are top feed injectors in the pics. They are definitely not stock RB25DET side feed injectors regardless of the colour.

x2

On another note, I had Denso 550cc injectors in my GTR when I first bought it and I'm pretty sure they were purple!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
×
×
  • Create New...