Jump to content
SAU Community

Recommended Posts

r32 gtst is 10 psi. i know because i have one.

r33 gtst and r34 gtt is 5 psi. i know because i have one. if the 33 and 34 was 7 psi, you could never have 5psi below 4500rpm as is the factory setup.

A 3rd option is to install a different wastgate actuator and the good news is the R32GTST item is exactly the same as the R34 except the spring inside is set for 10psi. R32 actuators can be hard to find but I think it’s the best option for this level of modification as boost spikes and boost creep are eliminated.

http://nissanskyline.6te.net/tuning_GTT.htm

could be incorrect though

r32 gtst is 10 psi. i know because i have one.

r33 gtst and r34 gtt is 5 psi. i know because i have one. if the 33 and 34 was 7 psi, you could never have 5psi below 4500rpm as is the factory setup.

my numbers are straight off the R32 and R33 service manuals

they indicate the minimum boost pressure before the actuator will start to open, that is, the minimum possible boost

HR32 is 12psi

R33 gtst AUTO is 5psi with 2psi bleed at 4500rpm by std solenoid, but base actuator is 5psi

R33 gtst MANUAL is 7psi with 2psi bleed at 4500rpm by std solenoid, but base actuator is 7psi

the service manuals could be wrong, but it is unlikely

didn't the rb25det and rb20det's have different actuators?

I'll be doing the same as you soon maddowse, did you find one?

yes i got it all done today !! i put new spark plugs in added the 3" bellmouth dump pipe and 3" cosco cat ,

also installed a blitz intercooler.

OK for starters i don't need to change the actuator as the boost didn't climb at all it was showing 12.5 on the guage before i installed everything and now its solid on 12psi .

the car now runs smoother (spark plugs) and also its now quieter ?? i thort opening the exhaust would make it louder but it hasn't and doesn't bother me one bit, response is still there so the cooler hasn't affected spool up time so all in all a good result . as for more power ill get back to you as its wet and I'm ether getting a engine light or if i turn off traction control I'm hitting rev limiter in seconds so i guess its hard to tell until its dry.

it doesnt seem to have any more power but i dont know if its just the gains are too small to notice or that maybe because its so much quieter now i feel i thinks its not i dont know , i should do a dyno run theres no point as i dont know what it was before the upgrades!!!.

can anyone claify for me i want to know if theres any boost leaks but i cant hear anything and the boost doesnt drop when the foots down but i dont feel the thrust of the turbo as much (agin it maybe because i cant hear the exhaust so my mind is tricking me or i could have been expecting huge gains so it feels less than i expected !!.

also i disconected the battery to put it in learn mode if that changes anything ??

sorry but but i am a noobe

r&r would be very noticeable mate, it will run like shit and be very unpleasant. O2 sensor will probably be due for a change, they only last like 60000km, but it won't impact on power, just on your freeway fuel economy.

Problem for us is there's no aftermarket O2 sensors like on the r33's and r32's, so we have to buy nissan, which are $200+.

You could dyno it and see if it's putting out the right amount of power by comparing it to the dyno thread. Or drive a friends corolla or whatever for some perception aligning :verymad:

ps: remember oil change after dyno mate

apparently mate, it's one of those things we're all meant to know lol. its mentioned here and there in the oils thread.

i think it's because the engine is pushed hard and gets hot, so its treated a bit like a drag or circuit day

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...